Dish Network 159263 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for 159263 Dish Network
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 48 |
| Size: | 14.83 MB |
Show table of contents
Read manual
Document Outline
- 159263_21.0 Guide_Cover
- 159263_21.0 Guide_Reference
- 159263_21.0 Guide_C1
- 159263_21.0 Guide_C2
- 159263_21.0 Guide_C3
- 159263_21.0 Guide_C4
- 159263_21.0 Guide_C5
- 159263_21.0 Guide_C6
- 159263_21.0 Guide_C7
- 159263_21.0 Guide_C8
- 159263_21.0 Guide_C9
- 159263_21.0 Remote Control
- Table of Contents
- Quick Setup
- Operation
- 1 Turn the equipment on.
- 2 Find the brand name of the equipment listed in the code tables that start on page 17.
- 3 Press and hold the mode button for the equipment until all the other mode buttons light up, and then release the button. The mode button flashes.
- 4 For Aux mode only. Press 0 for a second TV, or 1 for a second DVD/VCR, or 2 for a tuner, amplifier, or audio receiver.
- 5 Enter one of the three-digit equipment codes from the table using buttons on the number pad.
- 6 If you want to program Limited Mode, press 1. If not, skip to step 7.
- 7 Press Pound (#).
- 8 Press Power to turn off the equipment. If the equipment does not turn off, go to step 10.
- 9 Turn the equipment back on and try some other buttons to make sure they work. If the code works for other buttons, stop here.
- 1 Turn the equipment on.
- 2 Press and hold the mode button until all the other mode buttons light up, and then release the button. The mode button flashes.
- 3 For Aux mode only. Press 0 for a second TV, 1 for a second DVD/VCR, or 2 for a tuner, amplifier, or audio receiver. Then press the Star (*) button.
- 4 Press PoweR.
- 5 Press either the Up or Down arrow repeatedly until the equipment turns off.
- 6 Press Pound (#).
- 7 Turn the equipment back on and try some other buttons to make sure they work.
- 8 If necessary, repeat this procedure until you’ve tried all the codes.
- 1 Press and hold the Aux mode button until all mode buttons are lit, then release it. The aux mode button will blink.
- 1 Press and hold the TV mode button until all mode buttons are lit, then release it. The TV mode button will blink.
- 2 Press the Pound (#) button.
- 2 Press the Pound (#) button.
- 3 Press the plus (+) side of the Volume button.
- 3 Press the plus (+) side of the Volume button.
- 4 Press the 0 number button.
- 4 Press the 0 number button.
- 5 Press the Pound (#) button. The AUX mode button flashes three times.
- 5 Press the Pound (#) button. The TV mode button flashes three times.
- 6 Press the sat mode button.
- 6 Press the sat mode button.
- 7 Press the plus (+) and minus (-) sides of the volume button.
- 7 Press the plus (+) and minus (-) sides of the volume button.
- 8 Your tuner/amplifier’s volume changes and the aux mode button lights instead of the TV mode button.
- 8 Your TV’s volume changes and the TV mode button lights instead of the AUX mode button.
- 1 Turn on the other receiver and open the System Information screen. (For help opening the System Information screen, refer to the user guide for the other receiver.)
- 2 Press and hold the Aux button until all the mode buttons light up, and then release the button. The Aux button flashes.
- 3 Use the Number Pad on the remote control to enter a 3, followed by the address you wrote down in step 1.
- 4 Press Pound (#). The Aux button blinks three times.
- 5 Press Record to verify that the address in the remote control now matches the address for the receiver.
- 1 Press and hold the mode button for the equipment you want the remote control to operate. When all the mode buttons light up, release the button-the selected mode button should now be flashing.
- 2 Press the Pound (#) button twice. The mode button flashes the number for each digit of the equipment code, with a pause between the groups of flashes. A quick flash is for zero.
- 1 You can follow the instructions for using equipment codes to program a specific mode, and then learn commands that add new or ...
- 2 Each button on this remote learns a command from the equipment’s original remote control. For this type of learning, any button without a learned command will have no function for that equipment.
- 1 Ensure the DISH Network remote control is programmed to the desired remote address (see Changing the Remote and Receiver Address on page 13).
- 2 Place both your DISH Network remote and the original equipment’s remote control on a flat, stable surface.
- 3 On the DISH Network remote, press and hold the mode button for your equipment for about three seconds until all the mode buttons light up, and then release it. Your selected mode button will blink.
- 4 To start learning commands for this mode:
- 5 Point the front of the original equipment’s remote to face the small square (IR window) on the front, left-hand side of DISH’s remote, as shown below and on page C-1.
- 6 On the DISH Network remote, press the button you want to teach.
- 7 On the original equipment's remote control, press and hold the button you want learned. If the DISH Network remote learns the ...
- 8 After a button has learned a command successfully, repeat step 6 and step 7 until all commands you want have been learned.
- 9 To end the learning sequence:
- 1 Program the DISH Network remote to the desired remote address (see Changing the Remote and Receiver Address below).
- 2 Hold the SAT mode button until all mode buttons light, then release the button.
- 3 Press the POWER button (not TV Power).
- 4 Press VOLUME UP for discrete power on, or VOLUME DOWN for discrete power off.
- 5 Press any other button when you are done to end this procedure.
- 1 Press System Info on the receiver's front panel. The System Information screen displays and shows the Primary Remote Address (for TV1, typically using IR) and the Secondary Remote Address (for TV2, typically using UHF).
- 2 Press and hold SAT on your remote control for about three seconds, until all of the mode buttons light up, and then let go of SAT.
- 3 Add one to the address that you wrote down in step 1, and use the Number Pad to enter that number (between 1 and 28).
- 4 Press Pound (#). If you entered the address correctly, the SAT button will flash three times. Write down the number you entered in the space provided on the inside back cover of this guide.
- 5 Press Record. Make sure the Secondary Remote Address you see on the System Information screen is the same as the one you entered in step 3. If it isn't, the remote control cannot operate the receiver. Press RECORD a second time.
- 6 Select Done to close the System Information screen.
- 1 Remove the battery cover from the remote control.
- 2 Use a small screw driver or a paper clip to carefully change the setting.
- 3 Put the battery cover back on the remote control.
- 4 Use the SysTEM Info button on the front panel to open the System Information screen.
- 5 Press Record on the remote control.
- 6 Make sure the remote address on the receiver’s System Information screen shows the correct information:
- 1 Make sure the key is installed as described on pages C-1 and C-2.
- 2 Make sure the UHF Antenna is attached to the Remote Antenna input on the back of the receiver.
- 3 Using the receiver’s front panel buttons, press Menu. Select the following on-screen items in this sequence:
- a. System Setup.
- b. Installation.
- c. TV1 UHF Pro Setup.
- 4 Select Enable from the TV1 UHF Pro Setup screen.
- 5 Select System Info to open the System Information screen.
- 6 Use the ARROW buttons to move the highlight to the TV1 remote address (the Rem Addr box as shown below). This is important-if ...
- 7 Press the Record button on the green TV1 remote control you are setting up. If you get a warning that tells you to pick another address, continue on to the next step. If no warning appears, go to step 12 of this procedure.
- 8 On the remote control, press and hold the Sat mode button for about three seconds, until all the mode buttons light up, and then release the Sat button. The Sat mode button will blink.
- 9 Use the number buttons to enter any number from 1 to 28, except for the address shown for on your screen.
- 10 Press the Pound (#) button. If you entered the address correctly, the Sat mode button will flash three times. Press Record on the remote.
- 11 Make sure the System Information screen shows UHF and that this address matches the number that you entered in step 9.
- 12 Select Done to close the System Information screen. If nothing happens, press Record, and then select Done.
- 1. Review this User Guide.
- 2. See Troubleshooting on page 31.
- 3. Call the Customer Service Center at 1-800-333-DISH (3474). Have the date of purchase and your customer account number ready.
- a. If the representative finds you should return the remote control, you’ll get a telephone number to call for a Return Authorization (RA) number. Before shipping any equipment to us, you must get a Return Authorization number.
- b. You must package returned equipment the right way. Follow the instructions the representative gives you.
- c. Write the RA number in large, clearly visible characters on the outside of the shipping box used to return the equipment. To ...
- d. We will:
- 1. this device may not cause harmful interference, and
- 2. this device must accept any interference received, including interference that may cause undesired operation.
- Table of Contents
- 159263_21.0 Guide_Back Cover