Document Outline

• Elo Entuitive Touchmonitor User Guide
• Table of Contents
• Chapter 1 Introduction
  • Product Description
  • Precautions
  • About the Product
• Chapter 2 Installation and Setup
  • Unpacking Your Touchmonitor
    • Rear View
  • Connecting Your Touchmonitor
    • Video Cable Connection
      • 1 Set the touchmonitor on a solid horizontal surface, such as a table or desk.
      • 2 Connect the female end of the video cable connector to the back of the LCD monitor, and connect...
      • 3 Secure the cable to your touchmonitor and computer by tightening the screws on the connector cl...
    • Touchscreen Cable Connection
      • 1 Connect the female end of the 9-pin touchscreen RS-232 cable to the serial port on the back of ...
      • 2 Connect the male end of the cable to the serial touchscreen connector on your touchmonitor.
      • 3 Secure the cable to your touchmonitor and computer by tightening the screws on the connector cl...
    • Power Cable Connection
      • 1 Depending on where you live, you will use either the European or US/Canadian power cable. Conne...
      • 2 Connect the Brick power supply into the power port on the touchmonitor.
  • Video Input Pin Assignment
  • Installing the Driver Software
    • Installing the Serial Touch Driver for Windows XP, Windows 2000, Me, 95/98 and NT 4.0
    • Note:
      • 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
      • 2 Follow the directions on the screen to complete the driver setup for your version of Windows.
      • 1 Click Start > Run.
      • 2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
      • 3 Click Open, then OK to run EloCd.exe.
      • 4 Follow the directions on the screen to complete the driver setup for your version of Windows.
      • Installing the Serial Touch Driver for MS-DOS and Windows 3.1
        • 1 Insert the CD-ROM in your computer’s CD-ROM drive.
        • 2 From DOS, type d:\EloDos_W31 to change to the correct directory on the CD-ROM (your CD-ROM driv...
        • 3 Type install and press Enter to start the installation.
        • 4 Align the touchscreen.
        • 1 Type INSTALL at the DOS prompt in the directory containing the driver install files.
        • 2 INSTALL asks you to select the software to install. Then choose d:\EloDos_W31 from the displaye...
        • 3 INSTALL also asks you for the paths to use during installation, or you may use its defaults. IN...
• Chapter 3 Operation
  • Touchmonitor Controls
    • Setting the Refresh Rate
      • 1 Go to the configuration window (Start>Settings>Configuration window).
      • 2 Double-click on the Display icon.
      • 3 Click on the Settings tab.
      • 4 Click on the Advanced button.
      • 5 Click on Adapter and select 60Hz from the list.
      • 6 Click on Apply to accept the selected value.
    • Adjustments
      • Figure 3.1 Touchmonitor Controls
  • Screen Adjustments
    • 1 Push the MENU button once to display the OSD screen. The resolution and frequency are displayed...
    • 2 Push the or button to select the item you want to adjust. The selected item will be highlighted.
    • 3 Push the SELECT button to adjust the highlighted item.
    • 4 Push the or button to adjust the selection.
    • 5 After making the adjustment, push the MENU button to return.
    • 6 The display unit automatically saves the new settings in 1 second after your last adjustment an...
    • Direct Access Buttons
      • Auto Adjust
    • OSD Lock/Unlock
      • 1 Press the MENU and Power button together for 2 or 3 seconds.
      • 2 Select the OL icon.
      • 3 Select Yes.
      • 4 Power the monitor off then on.
      • 5 Press the MENU button. The status is OSD lock on the user mode.
      • 1 Press the MENU and Power button together for 4 or 5 seconds on the OSD lock status.
    • Power Lock/Unlock
      • 1 Press the MENU and Power button together for 2 or 3 seconds.
      • 2 Press the MENU button and select the PL icon.
      • 3 Select Yes.
      • 4 Press the MENU button and select the OL icon.
      • 5 Select No.
      • 6 Power the monitor off then on.
      • 7 Press the Power button. The status is Power lock on the user mode.
      • 1 Press the MENU and Power button together for 4 or 5 seconds on the Power lock status.
    • OSD and Power Lock/Unlock
      • 1 Press the MENU and Power button together for 2 or 3 seconds.
      • 2 Press the MENU button and select the PL icon.
      • 3 Select Yes.
      • 4 Power the monitor off then on.
      • 5 Press the MENU and Power button. The status is OSD and Power lock on the user mode.
      • 1 Press the MENU and Power button together for 4 or 5 seconds on the OSD and Power lock status.
  • OSD Adjustments
    • BRIGHTNESS
    • CONTRAST
    • COLOR CONTROL
    • YUV COLOR
      • HUE
      • FLESH TONE
    • MISCELLANEOUS
      • RECALL
      • OSD TIMER
      • OSD POSITION
    • AUTO ADJUST
    • LANGUAGE
    • H/VPOSITION
      • H-POSITION
      • V-POSITION
    • CLOCK PHASE
      • PHASE
      • CLOCK
• Chapter 4 Troubleshooting Tips
• Appendix A Native Resolution
• Appendix B Touchmonitor Safety
  • Care and Handling of Your Touchmonitor
• Appendix C Technical Specifications
  • Preset Timing Table
  • VESA Mounting
    • Touchmonitor Specifications
    • AccuTouch Touchscreen Specifications
    • IntelliTouch Touchscreen Specifications
  • 17" LCD Desktop Touchmonitor (ET1724L-XSWB-1) Dimensions
• Regulatory Information
• Index
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • L
  • M
  • N
  • O
  • P
  • R
  • S
  • T
  • U
  • V
  • X