Document Outline

• Front Cover
• FOR SAFE OPERATION
• Revision History
• Preface
• Important Alert Items
• MANUAL ORGANIZATION
• REFERENCED STANDARDS
• Contents
  • Illustrations
    • FIGURES
    • TABLES
• CHAPTER 1 General Description
  • 1.1 Features
    • 1.1.1 Performance and Functions
    • 1.1.2 Reliability
    • 1.1.3 Maintainability/operability
    • 1.1.4 Adaptability
    • 1.1.5 Interface
  • 1.2 Configuration of Optical Disk Drive
    • 1.2.1 Appearance
    • 1.2.2 Configuration
    • 1.2.3 Mechanical section
    • 1.2.4 Control circuit section
• CHAPTER 2 Specifications
  • 2.1 Specifications of Optical Disk Drives
    • 2.1.1 Catalog and order numbers
    • 2.1.2 Specifications of drives
    • 2.1.3 Environmental and power requirements
    • 2.1.4 Error rate
    • 2.1.5 Reliability
  • 2.2 Specifications of Optical Disk Cartridges
    • 2.2.1 Recommended optical disk cartridges
    • 2.2.2 Appearance
    • 2.2.3 Specifications of disk
  • 2.3 Defect Management
    • 2.3.1 Defect management schematic diagram
• CHAPTER 3 Installation Requirements
  • 3.1 Environmental Requirements
    • 3.1.1 Temperature measurement points
    • 3.1.2 Temperature requirements
    • 3.1.3 Temperature rise
    • 3.1.4 Air flow
    • 3.1.5 Air cleanliness
  • 3.2 Mounting Requirements
    • 3.2.1 Outer dimensions
    • 3.2.2 Installation direction
    • 3.2.3 Center of gravity
    • 3.2.4 Precautions on mounting
  • 3.3 Power Supply Requirements
  • 3.4 Connection Requirement
    • 3.4.1 Connectors and terminals
    • 3.4.2 Cable connection requirements
    • 3.4.3 External operator panel
    • 3.4.4 External operator panel settings (CNH2)
• CHAPTER 4 Installation
  • 4.1 Notes on Drive Handling
  • 4.2 Connection Modes
  • 4.3 Settings
    • 4.3.1 Setting switches (SW1)
    • 4.3.2 Setting of supplying power to SCSI terminating resistor
    • 4.3.3 SCSI terminating resistor mode
  • 4.4 Mounting
    • 4.4.1 Checks before mounting the drive
    • 4.4.2 Mounting procedure
  • 4.5 Cable Connections
  • 4.6 Operation Confirmation and Preparation for Use after Installation
    • 4.6.1 Confirming initial operations
    • 4.6.2 SCSI connection check
  • 4.7 Dismounting Drive
• CHAPTER 5 Operation and Cleaning
  • 5.1 Operation of Optical Disk Drive
    • 5.1.1 Appearance of optical disk drive
    • 5.1.2 Precautions
    • 5.1.3 Inserting an optical disk cartridge
    • 5.1.4 Removing an optical disk cartridge
  • 5.2 Cleaning of Optical Disk Drive
  • 5.3 Operation of Optical Disk Cartridge
    • 5.3.1 Appearance
    • 5.3.2 Write protect tab
    • 5.3.3 Precautions
  • 5.4 Cleaning the Optical Disk Cartridge
    • 5.4.1 Cleaning tool for optical disk cartridge
    • 5.4.2 Cleaning of optical disk cartridge
• CHAPTER 6 Diagnostics and Maintenance
  • 6.1 Diagnostics
    • 6.1.1 Initial self-diagnostics
    • 6.1.2 Diagnostic command
    • 6.1.3 Test program
  • 6.2 Maintenance Information
    • 6.2.1 Maintenance requirements
    • 6.2.2 Revision number
• CHAPTER 7 SCSI BUS
  • 7.1 System Configuration
  • 7.2 Interface Signal Definition
  • 7.3 Physical Requirements
    • 7.3.1 Interface connector
    • 7.3.2 Interface cable
  • 7.4 Electrical Requirements
    • 7.4.1 SCSI interface
    • 7.4.2 Power supply for terminating resistor
    • 7.4.3 Signal driving conditions
  • 7.5 Timing Rule
  • 7.6 Bus Phases
    • 7.6.1 BUS FREE phase
    • 7.6.2 ARBITRATION phase
    • 7.6.3 SELECTION phase
    • 7.6.4 RESELECTION phase
    • 7.6.5 INFORMATION TRANSFER phases
    • 7.6.6 COMMAND phase
    • 7.6.7 DATA phase
    • 7.6.8 STATUS phase
    • 7.6.9 MESSAGE phase
    • 7.6.10 Signal requirements concerning transition between bus phases
    • 7.6.11 Time monitoring feature
  • 7.7 Bus Conditions
    • 7.7.1 ATTENTION condition
    • 7.7.2 RESET condition
  • 7.8 Bus Sequence
• Glossary
• Acronyms and Abbreviations
• Index
• READER’S COMMENT FORM
• Back Cover