Document Outline

• MDE-4820H 8 PORT COMMVERTER OPERATION AND INSTALLATION MANUAL
  • GENERAL DESCRIPTION
    • 1.1. SCOPE
    • 1.2. MANUAL ORGANIZATION
    • 1.3. GENERAL DESCRIPTION
    • 1.4. MODULES
      • 1.4.1. Modules
    • 1.5. SPECIFICATIONS
      • 1.5.1. Communication Rates
      • 1.5.2. Electrical
      • 1.5.3. Mechanical Pump Rates
      • 1.5.4. Mechanical
      • 1.5.5. Environmental
    • 1.6. PROTECTION
  • APPLICATIONS
    • 2.1. SCOPE
    • 2.2. COMMVERTER SYSTEM ARCHITECTURE
      • 2.2.1. General
      • 2.2.2. System Architecture 1: Centralized at the Station Office
      • 2.2.3. System Architecture 2: Moved to the Isle Side
      • 2.2.4. System Architecture 1: Using an OrPT and/or µVIT on the Isles
    • 2.3. TYPES OF FUEL PUMP AND THEIR COMMUNICATION METHOD
    • 2.4. CONNECTORS
      • 2.4.1. General
      • 2.4.2. Mating a Connector
    • 2.5. LAN to RS485 APPLICATION
      • 2.5.1. RS485 Connector Pinout
      • 2.5.2. RS-485 Module Jumpers
    • 2.6. LAN to RS-232 APPLICATION
      • 2.6.1. RS-232 Connector Pinout
    • 2.7. LAN to CURRENT LOOP
      • 2.7.1. LAN to Current Loop Application
      • 2.7.2. Current Loop Connector Pinout
      • 2.7.3. Current Loop Module Jumpers
      • 2.7.4. Current Loop Electronic Devices (Pump or any Current Loop Devices)
      • 2.7.5. Wayne Pump Configuration Example
      • 2.7.6. Gilbarco Legacy & Gasboy 8800 Current Loop Electronic Pumps Configuration
      • 2.7.6.1. SiteOmat Configuration for Gilbarco Legacy & Gasboy 8800 Current Loop Electronic Pumps
    • 2.8. LAN to TOKHEIM APPLICATION
      • 2.8.1. Tokheim Connector Pinout
      • 2.8.2. Tokheim Module Jumpers
      • 2.8.3. Tokheim Electronic Devices (Pump or any Tokheim Devices)
      • 2.8.4. Addressing Dual-Sided Tokheim Pumps
    • 2.9. 4xCONTACTOR APPLICATION
      • 2.9.1. 4x Contactor Connector Pinout
      • 2.9.2. 4xContactor Module Jumpers
      • 2.9.3. Station Setup
      • 2.9.4. Pump Server Setup
      • 2.9.5. 8 Port CommVerter Setup
    • 2.10. LAN to RS422 APPLICATION
      • 2.10.1. RS422 Module Application
      • 2.10.2. RS-422 Connector Pinout
      • 2.10.3. SubRS422 Module Application
    • 2.11. LAN TO NUOVO PIGNONE APPLICATION
      • 2.11.1. Nuovo Pignone Connector Pinout
      • 2.11.2. COPTRON Communication to Nuovo Pignone Card
    • 2.12. LAN TO RS232/485 APPLICATION
      • 2.12.1. RS-232/485 Connector Pinout
    • 2.13. MECHANICAL PUMP INTERFACE (MPI-C)
      • 2.13.1. MPI-C Connector Pinout and Signals
      • 2.13.2. Mechanical Pump - Pulser Connections
      • 2.13.2.1. Pulse Rate
      • 2.13.2.2. Interface Connections
      • 2.13.3. Pulse Divider
      • 2.13.4. Description for LED's on the MPI-C board
    • 2.14. 5-PORT LAN SWITCH
    • 2.15. CETIL ER3 MODULE
      • 2.15.1. Sub module (Suspend Resume Relay Card)
      • 2.15.2. Sub Module Pumalan
    • 2.16. DOOR OPEN DETECTION
      • 2.16.1. Door Open Detector Installation
  • COMMVERTER DESCRIPTION
    • 3.1. SCOPE
    • 3.2. PHYSICAL
      • 3.2.1. Housing
      • 3.2.2. Front and Rear Panel
    • 3.3. LED INDICATORS
      • 3.3.1. General
      • 3.3.2. Configuration
    • 3.4. MAIN BOARD CONNECTORS
    • 3.5. MAIN BOARD JUMPERS
    • 3.6. CHANGING THE IP ADDRESS
  • INSTALLATION AND GROUNDING
    • 4.1. GENERAL
    • 4.2. PRELIMINARY PROCEDURES
      • 4.2.1. Unpacking and Inspection
      • 4.2.2. Installation Equipment
      • 4.2.3. Protective Procedures
    • 4.3. INSTALLING THE COMMVERTER
      • 4.3.1. General
      • 4.3.2. Desktop Installation
      • 4.3.3. Cables’ Connections
    • 4.4. GROUNDING THE COMMVERTER
      • 4.4.1. General
      • 4.4.2. Grounding – General Concept
      • 4.4.3. Grounding the 8-port Commverter (without RS485 card)
      • 4.4.4. Grounding the 8-port Commverter (without RS485 card)
      • 4.4.5. Verifying the Grounding
    • 4.5. SUBMODULE INSTALLATION AND GROUNDING
      • 4.5.1. Installation of Protective Isolator Sheet
      • 4.5.2. Connector Mechanical Outline – Check Procedure
      • 4.5.3. SubModule - Grounding
      • 4.5.4. SubModule Installation – Wiring Label Placing
    • 4.6. SUBMODULE REPLACEMENT - REMOVAL INSTRUCTIONS
      • 4.6.1. General
      • 4.6.2. Removal Tool – Spring ARC
      • 4.6.3. Removal Tool – Procedures
  • SETUP AND CONFIGURATION
    • 5.1. GENERAL
    • 5.2. DISPLAYING THE MAIN PAGE
    • 5.3. ETHERNET SETUP PROCEDURES
    • 5.4. TCP PORTS SETUP PROCEDURES
    • 5.5. SERIAL PORTS SETUP PROCEDURES
    • 5.6. PIPES SETUP PROCEDURES (NOT TO BE USED)
    • 5.7. DIGITAL I/O PORTS SETUP PROCEDURES (NOT TO BE USED)
      • 5.7.1. Door Open Detection Digital I/O Port Setup
    • 5.8. ADMINISTRATION TASKS PROCEDURES
      • 5.8.1. EEPROM Save Procedures
      • 5.8.2. Service Web Ports – TCP/IP Timeout Definition Procedures
      • 5.8.3. Login Information Definition Procedures (Not to be used)
    • 5.9. SYSTEM MONITOR INFORMATION SCREENS
      • 5.9.1. General
      • 5.9.2. Counters Description
    • 5.10. TERMINAL SCREEN (Not to be used)
  • CHECKS AND TROUBLESHOOTING
    • 6.1. GENERAL
    • 6.2. POST-INSTALLATION CHECKS
  • APPENDIX A UPGRADING THE COMMVERTER TO A NEW VERSION
    • GENERAL
    • APPLICABILITY
    • UPGRADING PROCEDURES
    • PRELIMINARY SETUP PROCEDURES
    • SETTING THE APPLICATION PARAMETERS IN THE DHCP SERVER
    • SETTING THE APPLICATION PARAMETERS
    • FINAL PROCEDURES
    • MPI-C - DYNAMIC PULSER SAMPLING PERIOD
    • 1. GENERAL
    • 2. CALCULATION
    • 3. SETTING THE MPI-C
  • APPENDIX B PLANNING AND CONNECTION OF PI’S
    • GENERAL
    • CONNECTORS
    • WORKING WITH COMMVERTER