Document Outline

• Table of Contents
• 1 Introduction
  • Caution
  • Terms
  • The Gilbarco interface unit
    • Differences between interface versions 1.2 and 2.0
    • Differences between interface versions 2.0 and 2.1
  • Potential problems
    • Cash/credit buttons and more than two price levels
    • Many price levels on multiple hose units
    • Measured totals for blended products not available
    • Cash/credit select and Site Controller I
    • Gallon cutoffs on multiple hose or fuel units
    • Large gallon limits
    • Product restriction on multiple hose or fuel units
    • Volume display at Check Point or Profit Point
    • Advantage version 70.1 firmware
    • MPD-2
    • MPD Pro Blender
    • Modular MPD-3 version 53.7 firmware
    • Multiple price levels on other Gilbarco pumps
    • Incompatible pump firmware releases
    • Loading Master Key
    • Network Key Parity
    • Contract Prices
    • More than 16 CRINDs
    • Blenders and Gascard Network
    • Don’t leave GSM powered down
    • Broadcast messages
    • Grade restrictions with pre-Advantage MPDs
    • Six-digit money on some pumps, five-digit on others
• 2 Installation
  • What to do first
  • Things to watch out for
    • Correct the indicated CRIND two-wire address
    • Don’t use gallon limits on multi-fuel pumps
    • Use $999 limits only with cash/credit select
    • Use only grade 1 with Highlines
    • Set correct level at price bars
    • Use reader AUTO YES only with CRINDs
    • Install K5 and K6
    • Do memory reset before checkout
  • Starting up the site
    • Determine programming information
    • Worksheet Heading Description
    • Other configuration information
    • CRIND keypad programming
    • Switch settings for interface unit CPU board
    • DIP switch bank 2
    • DIP switch bank 3
    • DIP switch bank 4
  • Site Controller configuration
    • Prepare PUMP.BIN data
    • Prepare READER.BIN data
  • Program the Site Controller
  • Program the dispensers and CRINDS
  • Program the interface unit
    • CPU board jumpers
    • Current loop board jumpers
    • CPU board DIP switches
  • Connect and test the installation
    • Power wiring
    • RS485/422 site wiring
    • RS485/422 CRIND wiring
    • Current loop pump wiring
    • GSM Wiring
    • Initial power-up and checkout
  • Troubleshooting
    • If the system does not operate
    • Transferring from Gilbarco console to Gasboy interface
    • POS says PUMP BUSY on START key
    • Receipt lines wrap
    • Pumps work but prices won’t program correctly
    • Interface suddenly begins giving unexpected results
    • Messages on wrong CRIND or wrong pump activates
    • Single pump won’t come up
    • Site reports wrong fuel or wrong dollar amount
    • MPDs will pump only zero-quantity transactions
    • Zero quantity transaction
    • Unassigned Transactions
• 3 Hardware
  • Cabinet
  • External connections
    • Interface to distribution box current loop wiring (pumps)
    • Interface to distribution box RS485/422 wiring (CRINDs)
    • Site controller to interface RS485/422 wiring
    • Interface to GSM RS232 wiring
    • AC power inlet and fuse
    • Jumpers
    • DIP switches
    • Front panel CPU LEDs
  • Current loop driver board
    • Jumpers
    • Fuses
    • P1 and P2 current loop connectors
  • Building a dual input mode distribution box
• 4 Data monitor
  • Data monitor commands
    • Command: h
    • Command: w
    • Command: m
    • Command: sn
    • Command: n
    • Command: <space>
    • Command: ?
• Index
  • A
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • J
  • K
  • L
  • M
  • N
  • P
  • R
  • S
  • T
  • U
  • W