Document Outline

• HP UPS R5500 User Guide
• Notice
• Contents
• Component identification
  • UPS R5500 overview
  • UPS front panel
  • UPS front panel controls
  • UPS front panel LED indicators
  • UPS rear panel
    • REPO port
  • ERM rear panel
• Installation
  • Precautions
  • Preparing to install the hardware
    • Tools and materials
    • Selecting a site
    • Readying the equipment
  • Installing the mounting rails
  • Preparing the rails for integrated shipping
  • Installing the UPS
    • Removing the UPS battery bracket
    • Installing the batteries
    • Replacing the UPS battery bracket
    • Attaching the UPS front bezel
    • Switching on the UPS battery circuit breaker
    • Connecting the serial communications port
    • Connecting the REPO port
    • Connecting the ground bonding cable
    • Connecting the UPS to utility power
    • Connecting devices to the UPS
    • Connecting the UPS cord retention clips
    • Charging the UPS batteries
    • Starting power to the load
  • Installing the ERM
    • Attaching the ERM front bezel
    • Switching off the ERM circuit breaker
    • Connecting the ERM to the UPS
    • Switching on the ERM circuit breaker
    • Charging the ERM batteries
• UPS operations
  • Modes of operation
    • Standby mode
    • Operate mode
    • Configure mode
    • Auto-Bypass mode
  • Configuring the UPS
  • Testing the LEDs
  • Silencing an audible alarm
  • Verifying the REPO port connection
  • Powering down the UPS
• Power management
  • Power management software
• Maintenance
  • Removing the UPS front bezel
  • Removing the ERM front bezel
  • Replacing the UPS electronics module
  • Replacing the UPS option card
  • Replacing the batteries
    • Important battery safety information
    • Battery care and storage guidelines
    • UPS battery replacement procedure
  • Replacing the UPS
  • Replacing the ERM
  • Updating the UPS firmware
• Troubleshooting
  • LED and audible alarm troubleshooting
  • Battery condition
  • Bypass is out of range
  • General alarm condition
  • Input voltage is out of range
  • Insufficient warning of low batteries
  • Internal UPS fault condition
  • Low battery shutdowns
  • Overload condition
  • REPO condition
  • Site wiring condition
  • UPS does not provide the expected backup time
  • UPS does not start
  • UPS frequently switches between utility and battery power
  • UPS is in Auto-Bypass mode
  • UPS is on battery
  • Utility power condition
• Specifications
  • UPS physical specifications
  • ERM physical specifications
  • UPS input specifications
  • UPS output specifications
    • Power protection specifications
    • Voltage specifications
    • Output tolerance specifications
    • Output feature specifications
  • Battery specifications
  • Battery runtime for NA/JPN model
  • Battery runtime for INTL model
  • Environmental specifications
  • REPO port specifications
• Spares
  • Ordering spares
  • UPS spare parts list
  • Hardware options
• Technical support
  • Before you contact HP
  • HP contact information
• Warranty information
  • Limited warranty
  • $250,000 Computer Load Protection Guarantee
  • Pre-Failure Battery Warranty
• Regulatory compliance notices
  • Regulatory compliance identification numbers
  • Federal Communications Commission notice
    • FCC rating label
    • Class A equipment
    • Class B equipment
  • Declaration of conformity for products marked with the FCC logo, United States only
  • Modifications
  • Cables
  • Canadian notice (Avis Canadien)
  • European Union regulatory notice
  • Japanese notice
  • BSMI notice
  • Battery replacement notice
  • Taiwan battery recycling notice
  • Power cord statement for Japan
• Electrostatic discharge
  • Preventing electrostatic discharge
  • Grounding methods to prevent electrostatic discharge
• Acronyms and abbreviations
• Index