Document Outline

• Safety information
• Contents
• Electromagnetic Compatibility (EMC)
  • Introduction
  • Installation and use
  • Assessment of area
  • Methods of reducing emissions
    • Mains supply
  • Maintenance of cutting equipment
  • Cutting cables
    • Equipotential bonding
    • Earthing of the workpiece
  • Screening and shielding
• Warranty
  • Attention
  • General
  • Patent indemnity
  • Limitation of liability
  • National and local codes
  • Liability cap
  • Insurance
  • Transfer of rights
• Specifications
  • Introduction
  • Duramax component weights
  • Duramax Hyamp component weights
  • Torch dimensions
    • Duramax 180° robotic torch dimensions
    • Duramax 90° robotic torch dimensions
    • Duramax 45° robotic torch dimensions
    • Duramax Hyamp 180° robotic torch dimensions
    • Duramax Hyamp 90° robotic torch dimensions
    • Duramax Hyamp 45° robotic torch dimensions
• Torch Setup
  • Robotic torch components
  • Install the torch
  • Disassemble the robotic torch
  • Mount the torch
  • Consumable life
  • Choosing the consumables
    • Duramax robotic torches
    • Duramax consumables
      • Duramax mechanized shielded 105 A*
      • Duramax mechanized shielded 45 A, 65 A, 85 A*
      • Duramax FineCut shielded 105 A*
      • Duramax FineCut shielded 65 A, 85 A*
      • *Ohmic-sensing retaining cap
      • Duramax mechanized unshielded 105 A
      • Duramax mechanized unshielded 45 A, 65 A, 85 A
      • Duramax FineCut unshielded 105 A
      • Duramax FineCut unshielded 65 A, 85
      • Duramax gouging 105 A
      • Duramax gouging 65 A, 85 A
    • Duramax Hyamp robotic torches
    • Duramax Hyamp consumables
      • Duramax Hyamp mechanized shielded 105 A/125 A*
      • Duramax Hyamp mechanized shielded 45 A, 65 A*
      • Duramax Hyamp FineCut shielded*
      • *Ohmic-sensing retaining cap
      • Duramax Hyamp gouging
    • Installing the consumables
  • Connecting the torch lead
  • Connecting a remote-start pendant
  • Connecting the machine interface cable
    • Machine interface pinout
    • Setting the five-position voltage divider
  • Using the cut charts
• Operation
  • Using the robotic torch
    • Using the Duramax robotic teach tool
    • Understand and optimize cut quality
      • Cut or bevel angle
      • Dross
      • Straightness of the cut surface
    • Piercing a workpiece using the robotic torch
    • Common machine-cutting faults
• Component Replacement
  • Duramax and Duramax Hyamp robotic torch overview
  • Disconnect the power, gas supply, and torch
  • Replacing the positioning barrel
    • Remove the positioning barrel
    • Install the positioning barrel
  • Replacing the torch body
  • Replacing the cap-sensor switch
  • Replacing the torch lead
• Maintenance and Parts
  • Perform routine maintenance
    • Routine maintenance tasks
  • Inspect the consumables
  • Duramax robotic torch replacement parts
    • Duramax 180° robotic torch
    • Duramax 90° robotic torch
    • Duramax 45° robotic torch
  • Duramax Hyamp robotic torch replacement parts
    • Duramax Hyamp 180° robotic torch
    • Duramax Hyamp 90° robotic torch
    • Duramax Hyamp 45° robotic torch
  • Accessory parts