Document Outline

• Before You Begin
  • Warranty Information
  • Safety Summary
  • Warnings and Cautions
  • About This Manual
• Other Intermec Manuals
• Chapter 1 - Getting Started
  • Getting to Know Your Printer
  • Preparing the Printer for Installation
    • Plugging in the Printer
    • Opening the Printer
    • Loading Media for Fanfold Printing
    • Printing the Hardware Configuration Test Label
  • Connecting the Printer to Your System
    • Connecting Your Printer to a PC
    • Connecting Your Printer to a Network
    • Connecting the Printer to an AS/400
    • Connecting the Printer to a Mainframe
    • Cabling in Noisy Electrical Environments
  • Configuring the Serial Port for Communications
  • Verifying Printer Communications With Your System
• Chapter 2 - Operating the Printer
  • Learning How to Operate the Printer
  • Understanding the Front Panel
    • Understanding the Front Panel LEDs
    • Using the Feed/Pause Button
  • Loading Media Into the Printer
    • Loading Roll Media for Straight-Through Printing
    • Loading Media for Self-Strip Printing
  • Loading Thermal Transfer Ribbon
  • Setting the Media Sensitivity Number
    • Setting the MSN for Intermec Media and Ribbon
    • Setting the MSN for Other Media and Ribbon
  • Communicating With the Printer
    • Using the PrintSet Software
    • Using Third-Party Software
    • Using Intermec Printer Language (IPL) Commands
    • Printing a Test Label
• Chapter 3 - Maintaining the Printer
  • Inspecting the Printer
  • Tools for Cleaning the Printer
  • Maintenance Schedule
    • Cleaning the Printhead
    • Cleaning the Printer Covers
    • Cleaning the Drive Roller and Tear Bar
    • Cleaning the Media Guides and Media Path
    • Cleaning the Label Sensors
• Chapter 4 - Troubleshooting
  • Troubleshooting Checklist
  • Printer Operation Problems
  • Print Quality Problems
  • Communication Problems and Preventing Data Loss
• Chapter 5 - Optimizing Printer Performance
  • Optimizing and Maintaining Print Quality
  • Correcting Uneven Print Quality
  • Adjusting the Print Darkness
  • Adjusting the Label Mark Sensor
  • Using the Printer Memory Efficiently
    • Increasing Throughput
• Chapter 6 - Using Test and Service Mode
  • Using Test and Service Mode Procedures
    • Printing Test Labels
    • Using Data Line Print
    • Resetting the Memory on Your Printer
  • Setting Configuration Commands in Test and Service Mode
    • Setting the Number of Dot Increments
    • Adjusting the Label Rest Point
    • Setting Emulation Mode
    • Using Forms Adjust
• Appendix A - Specifications
  • Printer Specifications
    • Specifications
  • Printer Options
    • Communication Interface
    • Finishers
  • Bar Code Symbologies Supported
    • 2D Symbologies
• Appendix B - Character Sets
  • International Character Sets
    • Advanced Character Table
    • Emulation Mode Character Table
    • IBM Translation Character Table
    • Code Page 850 Character Table
  • Extended Character Sets
• Appendix C - Communications Reference
  • Communication Protocols
    • Intermec Standard Protocol
    • XON/XOFF Protocol (Software and Hardware Flow Control)
    • XON/XOFF, No Status Protocol
    • Polling Mode D
    • Multi-Drop Protocol
    • User-Defined Protocol
    • Host Requirements
    • Communications Boundaries
  • Communications Interfaces
    • RS-232 Serial Interface
    • RS-422 Serial Interface
    • RS-485 Serial Interface
  • Printer Serial Port
• Appendix D - Full ASCII Table
  • Full ASCII Table
  • Full ASCII Control Characters Table
• Glossary
• Index
  • Numbers, A, B, C
  • D, E, F, G, H, I
  • L, M, N, O, P
  • R, S, T
  • U, W, X, Y