JAI AT-200GE Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for AT-200GE JAI
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 71 |
| Size: | 1.88 MB |
Show table of contents
Read manual
Document Outline
- AT-200GE
- JAI GigE VisionⓇ Camera operation manual
- Introduction
- Before using GigE Vision camera
- Software installation
- Camera Operation
- 1. General
- 2. Camera nomenclature
- 3. Main Features
- 4. Locations and Functions
- 4.1. Locations and Functions
- 4.2. Rear panel indicator
- 5. Pin Assignment
- 5.1. 12-pin Multi-connector (DC-IN/Trigg
- 5.2. Digital Output Connector for Giga
- 5.3. D-Sub 9pin connector (For GPIO)
- 5.4. DIP switch
- 5.4.1 SW-600
- 5.4.2 SW-100
- 6. Input and output circuits
- 6.1. Iris video output
- 6.2. Trigger input
- 6.3. XEEN output
- 6.4. Auto iris video output level
- 7. GPIO (General purpose inputs and ou
- 7.1. Overview
- 7.1.1 LUT (Look Up Table)
- 7.1.2 12-bit Counter
- 7.1.3 Pulse Generators (0 to 1)
- 7.2. Opto-isolated Inputs/Outputs
- 7.2.1 Recommended External Input circu
- 7.2.2 Recommended External Output circ
- 7.2.3 Optical Interface Specifications
- 7.3. Inputs and outputs table
- 7.4. Configuring the GPIO module (regi
- 7.4.1 Input/Output Signal Selector
- 7.4.2 12-bit counter
- 7.4.3 Pulse generators (20-bit x 4)
- 7.5. GPIO programming examples
- 7.5.1 GPIO Plus PWC shutter
- 7.5.2 Internal Trigger Generator
- 8. GigE®Vision Streaming Protocol (GVS
- 8.1. Digital Video Output (Bit Allocat
- 8.2. Bit Allocation (Pixel Format / Pi
- 8.2.1 GVSP_PIX_RGB8_PACKED (RGB 24bit
- 8.2.2 GVSP_PIX_RGB10V1_PACKED (RGB 32b
- 8.2.3 GVSP_PIX_RGB10V2_PACKED (RGB 32b
- 9. Functions and Operations
- 9.1. GigE Vision Standard Interface
- 9.2. Recommended Network Configuration
- 9.2.1 Guide line for network settings
- 9.2.2 Video data rate (network bandwid
- 9.2.3 Note for setting packet size
- 9.2.4 Calculation of Data Transfer Rat
- 9.2.5 Note for 100BASE-TX connection
- 9.3. Basic Functions
- 9.3.1 Basic construction
- 9.3.2 Modes of Operation
- 9.3.3 Partial scan (Fast Dump ON)
- 9.3.4 Vertical Binning (VB)
- 9.3.5 Electronic shutter (SM)
- 9.3.6 Auto-detect LVAL-sync / async ac
- 9.4. Pre-processing functions
- 9.4.1 Shading compensation
- 9.4.2 White balance
- 9.4.3 Linear matrix
- 9.4.4 Blemish compensation
- 9.4.5 Gamma setting (Look Up Table)
- 9.4.6 Knee compensation
- 9.5. Other functions
- 9.5.1 Test pattern generator (Address
- 9.5.2 Center marker
- 9.6. Sensor Layout and timing
- 9.6.1 CCD Sensor Layout
- 9.6.2. Horizontal timing (Normal conti
- 9.6.3 Vertical timing (Normal continuo
- 9.6.4 Horizontal timing (Partial scan
- 9.6.5 Vertical timing (Partial scan mo
- 9.6.6 Horizontal timing (Vertical binn
- 9.6.7 Vertical timing (vertical binnin
- 9.7. Operating Modes - Timing
- 9.7.1 Continuous operation
- 9.7.2 Edge Pre-select Trigger Mode (EP
- 9.7.3 Pulse Width Control Trigger Mode
- 9.7.4 Reset Continuous Trigger (RCT)
- 9.7.5 Sequential Trigger Mode (EPS)
- 9.7.6 Delayed Readout EPS and PWC Mode
- 9.7.7 Smearless mode
- 9.7.8 Optical Black transfer mode
- 9.7.9 Multi ROI mode (Multi Region of
- 9.8. Mode and functions matrix
- 10. External Appearance and Dimensions
- 11. Specifications
- 11.1. Camera sensitivity response
- 11.2. Specification table
- Register Map
- Appendix
- 1. Precautions
- 2. Typical Sensor Characteristics
- 3. Caution when mounting a lens on the
- 4. Caution when mounting the camera
- 5. Exportation
- 6. References
- Change history
- User's Record