Document Outline

• 1 Preliminary Considerations
  • 1.1 Trademarks and Copyright
  • 1.2 Customer Support
  • 1.3 Specific Document Information
  • 1.4 Latest Revision and Related Documents
  • 1.5 MRV Regulatory Compliance
  • 1.6 General Safety
  • 1.7 Electrical Safety
  • 1.8 Laser Safety
  • 1.9 Passive Laser Equipment Safety
• 2 Module Introduction
  • 2.1 Features
    • 2.1.1 Loopback
    • 2.1.2 Link Integrity Notification (LIN)
    • 2.1.3 LIN with Far End Fault Indication (FEFI)
    • 2.1.4 Redundancy
  • 2.2 Modes of Operation
    • 2.2.1 Dual Repeater (Fiber and Copper)
    • 2.2.2 Dual Converter
    • 2.2.3 Redundant Link
    • 2.2.4 Mixed-Media Switch (4-Port)
• 3 Preparation and Installation
  • 3.1 Unpacking the Fiber Driver Module
  • 3.2 Front Panel Description
    • 3.2.1 Distances
    • 3.2.2 SFP Ports
    • 3.2.3 LED Definitions
    • 3.2.4 LED Display Information
  • 3.3 DIP Switches
    • 3.3.1 Block Locations
    • 3.3.2 Switch Functions and Default Settings
  • Module Installation
  • Cleaning Fibers
    • 3.3.3 Working with SFPs
      • 3.3.3.1 Cleaning SFPs
        • 3.3.3.1.1 Requirements
        • 3.3.3.1.2 Procedure
      • 3.3.3.2 Mylar Tab SFP Modules
        • 3.3.3.2.1 Inserting a Mylar Tab SFP Module
        • 3.3.3.2.2 Removing a Mylar Tab SFP Module
      • 3.3.3.3 Actuator/Button SFP Modules
      • 3.3.3.4 Inserting an Actuator/Button SFP Module
        • 3.3.3.4.1 Removing an Actuator/Button SFP Module
      • 3.3.3.5 Bale Clasp SFP Module
        • 3.3.3.5.1 Inserting a Bale Clasp SFP/XFP Module into a Switching Module Port
        • 3.3.3.5.2 Removing a Bale Clasp SFP Module
• 4 Module Management
  • 4.1 Serial Console Interface
  • 4.2 MegaVisionJ Embedded GUI Management
  • 4.3 EM316LNXNM-OT Command Line Interface (CLI)
    • 4.3.1 EM316LNXNM-OT Boot and CLI Login
    • 4.3.2 CLI Navigation
    • 4.3.3 Login Context Commands and Examples
      • 4.3.3.1 “?”
      • 4.3.3.2 “show chassis”
      • 4.3.3.3 “show slots”
      • 4.3.3.4 “show version”
      • 4.3.3.5 “show log”
      • 4.3.3.6 “show groups”
      • 4.3.3.7 “show users”
      • 4.3.3.8 “show running-config”
      • 4.3.3.9 “show startup-config”
      • 4.3.3.10 Displaying and Saving System Parameters
    • 4.3.4 Configuration Context
      • 4.3.4.1 Restoring Default Parameters
      • 4.3.4.2 Configuring System Parameters
    • 4.3.5 Chassis Context
      • 4.3.5.1 “show”
      • 4.3.5.2 Other Commands
    • 4.3.6 Slot Context Commands and Examples
      • 4.3.6.1 “?”
      • 4.3.6.2 “list”
      • 4.3.6.3 “show”
    • 4.3.7 Port Context Commands and Examples
      • 4.3.7.1 “?”
      • 4.3.7.2 “list”
      • 4.3.7.3 “show”
      • 4.3.7.4 “description”
      • 4.3.7.5 “show defaults”
      • 4.3.7.6 “show config”
      • 4.3.7.7 “shutdown” and “no shutdown”
      • 4.3.7.8 “lin”
    • 4.3.8 RJ-45 Port Commands
      • 4.3.8.1 “auto-neg-adv”
      • 4.3.8.2 “auto-negotiation”
      • 4.3.8.3 “mdi-pinout”
      • 4.3.8.4 “duplex”
      • 4.3.8.5 “speed”
    • 4.3.9 SFP Port Commands
      • 4.3.9.1 “loopback”
      • 4.3.9.2 “lin”
      • 4.3.9.3 “select-link”
  • 4.4 Configuration Examples
    • 4.4.1 Repeater Mode
    • 4.4.2 Converter Mode
    • 4.4.3 Redundant Mode
    • 4.4.4 Switching Mode
• 5 Appendix
  • 5.1 Technical Specifications
  • 5.2 Operating Environment
  • 5.3 Troubleshooting