Document Outline

• 8 Intended use
  • Intended use
  • ( Safety instructions
    • Safety instructions
  • Before you switch ON the appliance
  • Delivery
    • 1. Check the packaging and dishwasher immediately for damage caused in transit. Do not switch on a damaged appliance, but contact your supplier.
    • 2. Please dispose of the packaging material in an environmentally friendly manner.
    • 3. Do not let children play with packaging and its parts. There is a risk of suffocation from collapsible boxes and film.
  • Installation
  • In daily use
  • Childproof lock (door lock)Door lock *
  • Damage
  • Disposal
    • 1. Make redundant appliances unusable to prevent subsequent accidents.
    • 2. Dispose of the appliance in a n environmentally friendly manner.
      • m Warning
      • Risk of injury!
      • m Warning
      • Risk of explosion!
      • m Warning
      • Risk of scalding!
      • m Warning
      • Risks to children!
  • 7 Protection of the environment
    • Protection of the environment
    • Packaging
    • Old appliances
  • * Getting to know your appliance
    • Getting to know your appliance
    • Control panel
    • Appliance interior
    • Overview of menu
  • + Water softening system/Special salt
    • Water softening system/Special salt
    • Setting
      • 1. Find out about the hardness value of your tap water. Your water utility company will help you with this.
      • 2. Set value can be found in the water hardness table.
      • 3. Open the door.
      • 4. Switch on ON/OFF switch (.
      • 5. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display.
      • 6. Release both buttons.
        • To change the setting:
      • 1. Press programme button 3.
      • 2. Press START button `.
      • 3. Close the door.
    • Water hardness table
    • Using special salt
      • 1. Open the screw-type cap of the compartment 1R.
      • 2. Fill the tank with water (only required when switching on the appliance for the first time).
      • 3. Then add dishwasher salt (not table salt or tablets).
    • Using detergents with salt componentDetergents with salt component
    • Switching off salt refill indicator/water softening systemSwitching off water softening system
      • m Caution
  • , Rinse aid
    • Rinse aid
    • 1. Open the dispenser 9" by pressing and lifting the plate on the cover.
    • 2. Carefully pour rinse aid up to the max. mark in the filler opening.
    • 3. Close cover until it clicks shut.
    • 4. To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth.
    • Setting amount of rinse aid
      • 1. Open the door.
      • 2. Switch on ON/OFF switch (.
      • 3. Hold down programme button # and press START button ` until •:‹... is indicated on the digital display.
      • 4. Release both buttons.
      • 5. Press programme button # until the factory set value §:‹… is indicated on the digital display h.
        • To change the setting:
      • 1. Press programme button 3.
      • 2. Press START button `.
      • 3. Close the door.
    • Switching off rinse aid refill indicator
  • - Utensils
    • Utensils
    • Not suitable
    • Glass and utensil damage
    • Loading the dishwasher
      • 1. Remove large food remnants. It is not necessary to prerinse utensils under running water.
      • 2. Place the utensils so that
    • Unloading the dishwasher
      • Note
    • Cups and glasses
    • Pans
      • Tip
      • Tip
    • Cutlery basket
    • Folding spikesFolding spikes *
    • Small accessories holder *Small accessories holder
    • Knife shelf *Knife shelf
    • Adjusting the height of the basketAdjusting the height of the basket *
      • Appliance height 81.5 cm
      • 22 cm
      • 30 cm
      • 24 cm
      • 28 cm
      • 27 cm
      • 25 cm
    • Top basket with side levers
      • 1. Pull out the top basket 1* out.
      • 2. To lower the basket, press in the left and then the right lever on the outside of the basket. In doing so, hold the sides of the basket along the upper edge to prevent it from suddenly dropping.
      • 3. To raise the basket, hold the basket on the sides of the upper edge and lift it up.
      • 4. Before re-inserting the basket again, ensure that it is at the same height on both sides. Otherwise, the appliance door cannot be closed and the upper spray arm will not be connected to the water circuit.
    • Top basket with upper and lower roller pairs
      • 1. Pull out the top basket 1* out.
      • 2. Remove the upper basket and re- attach it to the upper (stage 3) or lower (stage 1) rollers.
  • . Detergent
    • Detergent
    • Note
      • m Warning
    • Adding detergent
      • 1. If the detergent dispenser 9* is still closed, press the lock 92 to open the detergent dispenser.
      • 2. Close the cover on the detergent dispenser by sliding it up until the lock engages without difficulty.
        • Tip
    • Combination detergent
      • m Warning
      • m Warning
      • Notes
• / Overview of programmes
  • Overview of programmes
  • The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
    • Type of utensils
    • Type of soiling
    • Programme
    • Possible additional options
    • Programme sequence
  • Programme selection
  • Information for test institutes
  • 0 Additional options
    • Additional options
    • Express Wash/ Speed Perfect (VarioSpeed)Ÿ Express Wash/ Speed Perfect/ (VarioSpeed) *
    • Half load§ Half load *
    • · Hygiene *Hygiene
    • Ï Intensive zone *Intensive zone
    • ¿ Extra drying *Extra drying
  • 1 Operating the appliance
    • Operating the appliance
    • Programme data
    • Aqua sensorAqua sensor *
    • Switching on the appliance
      • 1. Turn on the tap fully.
      • 2. Open the door.
      • 3. Switch on ON/OFF switch (.
      • 4. Press the START button `.
      • 5. Close the door.
        • Note
    • Optical display while the programme is runningOptical display while the programme is running *
      • 1. Open the door.
      • 2. Switch on ON/OFF switch (.
      • 3. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display.
      • 4. Release both buttons.
      • 5. Press programme button # until the factory set value ‚:‹‚ is indicated on the digital display h.
        • To change the setting:
      • 1. By pressing the button 3, you can switch the function off ‚:‹‹ or on ‚:‹‚.
      • 2. Press START button `.
      • 3. Close the door.
    • Remaining running time display
    • Timer programmingTimer programming *
      • 1. Open the door.
      • 2. Switch on ON/OFF switch (.
      • 3. Press button P + until the digital display h jumps to œ:‹‚.
      • 4. Press P + or – button until the displayed time corresponds with your requirements.
      • 5. Press START button `, timer programming is activated.
      • 6. To delete timer programming, press the P + or – button until h œ:‹‹ is indicated on the digital display.
      • 7. Close the door.
    • End of programme
      • 1. Open the door.
      • 2. Switch on ON/OFF switch (.
      • 3. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display.
      • 4. Release both buttons.
      • 5. Press programme button # until the factory set value ›:‹ƒ is indicated on the digital display h.
        • To change the setting,
      • 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of ›:‹„ has been reached, the display jumps back to ›:‹‹ (off).
      • 2. Press START button `, the set value is saved.
      • 3. Close the door.
    • Automatic switch off after end of programme or interior light*Automatic switch off / interior light
      • 1. Open the door.
      • 2. Switch on ON/OFF switch (.
      • 3. Hold down programme button # and press START button ` until •:‹... is indicated on the digital display.
      • 4. Release both buttons.
      • 5. Keep pressing programme button # until the value ˜:‹... is indicated on the numerical display h.
        • To change the setting:
      • 1. Press programme button 3.
      • 2. Press START button `.
      • 3. Close the door.
    • Switching off the appliance
      • 1. Open the door.
      • 2. Switch off ON/OFF switch (.
      • 3. Turn off the tap (not applicable if Aqua-Stop fitted).
      • 4. Remove the utensils when they have cooled down.
        • Note
    • Interrupting the programme
      • 1. Open the door.
      • 2. Switch off ON/OFF switch (.
      • 3. To continue the programme, switch on the ON/OFF switch ( again.
      • 4. Close the door.
    • Terminating the programmeTerminating the programme (Reset)
      • 1. Open the door.
      • 2. Press START button ` for approx. 3 sec.
      • 3. Close the door.
      • 4. Open the door.
      • 5. Switch off ON/OFF switch (.
      • 6. Close the door.
    • Changing the programme
    • Intensive drying
      • 1. Open the door.
      • 2. Switch on ON/OFF switch (.
      • 3. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display.
      • 4. Release both buttons.
      • 5. Press programme button # until the factory set value š:‹‹ is indicated on the digital display h.
        • To change the setting,
      • 1. Press the button 3 to switch the Intensive drying on š:‹‚ or off š:‹‹.
      • 2. Press START button `.
      • 3. Close the door.
  • 2 Cleaning and maintenance
    • Cleaning and maintenance
    • Overall condition of the machine
      • m Warning
        • Health hazard
    • Special salt and rinse aid
    • Filters
      • 1. After each washing cycle check the filters for residue.
      • 2. Unscrew filter cylinder as illustrated and take out filter system.
      • 3. Remove any residue and clean filters under running water.
      • 4. Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system.
    • Spray arms
      • 1. Check outlet nozzles on the spray arms for blockages.
      • 2. Unscrew the upper spray arms 1B (1/4 revolution).
      • 3. Remove the lower spray arm 1J upwards.
      • 4. Clean spray arms under running water.
      • 5. Re-engage or screw on spray arms.
  • 3 Fault, what to do?
    • Fault, what to do?
    • Note
      • m Warning
    • Waste water pump
      • m Warning
        • Risk of cuts!
      • 1. First always disconnect the appliance from the power supply.
      • 2. Take out top basket 1* and bottom basket 1j.
      • 3. Remove the filters 1Z.
      • 4. Scoop out water, use a sponge if required.
      • 5. Prise out the white pump cover (as illustrated) using a spoon. Grip the cover on the crosspiece and lift diagonally inwards. Remove cover completely.
      • 6. Check impeller wheel and remove any foreign objects.
      • 7. Place cover in the original position and press down until it engages (click).
      • 8. Install filters.
      • 9. Re-insert baskets.
        • Fault table
          • Fault
          • Cause
          • Remedial action
  • 4 Customer service
    • Customer service
  • 5 Installation and connection
    • Installation and connection
    • 1. Checking appliance on delivery
    • 2. Installing the appliance
    • 3. Waste water connection
    • 4. Drinking water connection
    • 5. Electrical connection
    • Product package
    • Safety instructions
    • Delivery
    • Technical specifications
    • Installation
    • Waste-water connection
      • 1. The required work sequence can be found in the installation instructions. If required, fit a siphon with an drainage connection.
      • 2. Connect the waste-water hose to the drainage connection of the siphon with the enclosed parts.
    • Drinking water connection
      • 1. Fasten the drinking water connection to the tap according to the installation instructions using the enclosed parts.
      • 2. When replacing the appliance, always use a new water supply hose.
    • Warm water connection *Warm water connection
      • Setting hot water:
      • 1. Open the door.
      • 2. Switch on ON/OFF switch (.
      • 3. Hold down programme button # and press START button ` until •:‹... is indicated on the digital display.
      • 4. Release both buttons.
      • 5. Press programme button # until the factory set value ‘:‹‹ is indicated on the digital display h.
        • To change the setting:
      • 1. By pressing the 3 button, you can switch the hot water setting off ‘:‹‹ or on ‘:‹‚.
      • 2. Press START button `.
      • 3. Close the door.
    • Electrical connection
    • Removing the appliance
      • 1. Disconnect the appliance from the power supply.
      • 2. Turn off the water supply.
      • 3. Undo the waste water and drinking water connection.
      • 4. Loosen fastening screws for the furniture parts.
      • 5. If fitted, remove the base panel.
      • 6. Pull out the appliance, carefully pulling the hose behind.
    • Transportation
      • Drain the appliance according to the following steps:
      • 1. Turn on the tap.
      • 2. Open the door.
      • 3. Switch on ON/OFF switch (.
      • 4. Select programme with the highest temperature.
      • 5. Press START button `.
      • 6. Close the door.
      • 7. Open door after approx. 4 minutes.
      • 8. Press START button ` until ‹:‹‚ is indicated on the digital display.
      • 9. Close the door.
      • 10. Open door after approx. 1 minute.
      • 11. Switch off ON/OFF switch (.
      • 12. Turn off the tap, disconnect supply hose and drain water.
    • Protection against frostProtection against frost (Emptying the appliance)