Document Outline

• 1. Introduction
  • 1.1 Package Contents
  • 1.2 Product Description
  • 1.3 Product Features
  • 1.4 Product Specification
    • 1.4.1 ISW-1022M / ISW-1022MT Product Specification
    • 1.4.2 ISW-1022MPT Product Specification
    • 1.4.3 ISW-1033MT Product Specification
• 2. Installation
  • 2.1 Hardware Description
    • 2.1.1 Physical Dimension
    • 2.1.2 Front / Rear Panel
    • 2.1.3 Top View
    • 2.1.4 LED Indicators
      • ISW-1022M / ISW-1022MT LED Indicators
      • ISW-1033MT LED Indicators
      • ISW-1022MPT LED Indicators
  • 2.2 Install the Switch
    • 2.2.1 Installation Steps
    • 2.2.2 DIN-Rail Mounting
    • 2.2.3 Wall Mount Plate Mounting
    • 2.2.4 Wiring the Power Inputs
    • 2.2.5 Wiring the Fault Alarm Contact
    • 2.2.6 Wiring the Digital Inputs / Outputs (ISW-1033MT)
    • 2.2.7 Installing the SFP transceiver
• 3. Network Application
  • 3.1 Rapid Ring Application
  • 3.2 Coupling Ring Application
  • 3.3 Dual Homing Application
• 4. Console Management
  • 4.1 Connecting to the Console Port
  • 4.2 Pin Assignment
  • 4.3 Login in the Console Interface
  • 4.4 CLI Management
  • 4.5 Commands Level
• 5. Web-Based Management
  • 5.1 About Web-based Management
  • 5.2 Requirements
  • 5.3 Logging on the switch
  • 5.4 System
    • 5.4.1 System Information
    • 5.4.2 IP Configuration
    • 5.4.3 DHCP Server
      • 5.4.3.1 System configuration
      • 5.4.3.2 Client Entries
      • 5.4.3.3 Port and IP Bindings
    • 5.4.4 TFTP
      • 5.4.4.1 Update Firmware
      • 5.4.4.2 Restore Configuration
      • 5.4.4.3 Backup Configuration
    • 5.4.5 System Event Log
      • 5.4.5.1 Syslog Configuration
      • 5.4.5.2 System Event Log—SMTP Configuration
      • 5.4.5.3 System Event Log—Event Configuration
    • 5.4.6 Fault Relay Alarm
    • 5.4.7 SNTP Configuration
    • 5.4.8 IP Security
    • 5.4.9 User Authentication
  • 5.5 Port Management
    • 5.5.1 Port Statistics
    • 5.5.2 Port Control
    • 5.5.3 Port Trunk
      • 5.5.3.1 Aggregator setting
      • 5.5.3.2 Aggregator Information
      • 5.5.3.3 State Activity
    • 5.5.4 Port Mirroring
    • 5.5.5 Rate Limiting
  • 5.6 Protocol
    • 5.6.1 VLAN configuration
      • 5.6.1.1 VLAN Overview
      • 5.6.1.2 VLAN Configuration
      • 5.6.1.3 Port-based VLAN
      • 5.6.1.4 802.1Q VLAN
    • 5.6.2 Rapid Spanning Tree
      • 5.6.2.1 Theory
      • 5.6.2.2 RSTP Parameters
      • 5.6 2.3 Illustration of STP
      • 5.6.2.4 RSTP System Configuration
      • 5.6.2.5 Port Configuration
    • 5.6.3 SNMP Configuration
      • 5.6.3.1 System Configuration
      • 5.6.3.2 Trap Configuration
      • 5.6.3.3 SNMPV3 Configuration
    • 5.6.4 QoS Configuration
      • 5.6.4.1 QoS Policy and Priority Type
      • 5.6.4.2 Port-based Priority
      • 5.6.4.3 COS Configuration
      • 5.6.4.4 TOS Configuration
    • 5.6.5 IGMP Snooping
      • 5.6.5.1 Theory
      • 5.6.5.2 IGMP Configuration
    • 5.6.6 X-Ring
      • 5.6.6.1 X-Ring Application
      • 5.6.6.2 Coupling Ring Application
      • 5.6.6.3 Dual Homing Application
      • 5.6.6.4 X-Ring Configuration
  • 5.7 Security
    • 5.7.1 Security—802.1X/Radius Configuration
      • 5.7.1.1 Understanding IEEE 802.1X Port-Based Authentication
      • 5.7.1.2 System Configuration
      • 5.7.1.3 Port Configuration
      • 5.7.1.4 Misc Configuration
    • 5.7.2 MAC Address Table
      • 5.7.2.1 Static MAC Address
      • 5.7.2.2 MAC Filtering
      • 5.7.2.3 All MAC Addresses
      • 5.7.2.4 Multicast Filtering
  • 5.8 Digital Input/Output (ISW-1033MT)
    • 5.8.1 Digital Input
    • 5.8.2 Digital Output
  • 5.9 Power over Ethernet
    • 5.9.1 Power over Ethernet Powered Device
    • 5.9.2 Power Management:
  • 5.10 Factory Default
  • 5.11 Save Configuration
  • 5.12 System Reboot
• 6. Command Sets
  • 6.1 System Commands Set
  • 6.2 Port Commands Set
  • 6.3 Trunk Commands Set
  • 6.4 VLAN Commands Set
  • 6.5 Spanning Tree Commands Set
  • 6.6 QOS Commands Set
  • 6.7 IGMP Commands Set
  • 6.8 MAC / Filter Table Commands Set
  • 6.9 SNMP Commands Set
  • 6.10 Port Mirroring Commands Set
  • 6.11 802.1x Commands Set
  • 6.12 TFTP Commands Set
  • 6.13 SystemLog, SMTP and Event Commands Set
  • 6.14 SNTP Commands Set
  • 6.15 X-ring Commands Set
  • 6.16 PoE Command Set
• 7. SWITCH OPERATION
  • 7.1 Address Table
  • 7.2 Learning
  • 7.3 Forwarding & Filtering
  • 7.4 Store-and-Forward
  • 7.5 Auto-Negotiation
• 8. POWER OVER ETHERNET OVERVIEW
  • What is PoE?
  • The PoE Provision Process
    • Stages of powering up a PoE link
    • Line Detection
    • Classification
    • Start-up
    • Operation
    • Power Disconnection Scenarios
• Appendix A—RJ-45 Pin Assignment
  • A.1 Switch's RJ-45 Pin Assignments
  • A.2 10/100Mbps, 10/100Base-TX
• Appendix B Troubles shooting
• EC Declaration of Conformity