Document Outline

• 1.0 Introduction
  • 1.1 System requirements
  • 1.2 About Momentus 5400 FDE disc drives
    • 1.2.1 Drive state upon shipment
• 2.0 Drive specifications
  • 2.1 Specification summary
  • 2.2 Formatted capacity
  • 2.3 Default logical geometry
  • 2.4 Physical organization
  • 2.5 Recording and interface technology
  • 2.6 Physical characteristics
  • 2.7 Seek time
  • 2.8 Time to ready
  • 2.9 Power specifications
    • 2.9.1 Power consumption
      • 2.9.1.1 Typical current profile
    • 2.9.2 Conducted noise
    • 2.9.3 Voltage tolerance
    • 2.9.4 Power-management modes
  • 2.10 Environmental specifications
    • 2.10.1 Ambient temperature
    • 2.10.2 Temperature gradient
    • 2.10.3 Humidity
      • 2.10.3.1 Relative humidity
      • 2.10.3.2 Wet bulb temperature
    • 2.10.4 Altitude
    • 2.10.5 Shock
      • 2.10.5.1 Operating shock
      • 2.10.5.2 Nonoperating shock
    • 2.10.6 Vibration
      • 2.10.6.1 Operating vibration
      • 2.10.6.2 Nonoperating vibration
  • 2.11 Acoustics
  • 2.12 Electromagnetic immunity
  • 2.13 Reliability
  • 2.14 Agency certification
    • 2.14.1 Safety certification
    • 2.14.2 Electromagnetic compatibility
    • 2.14.3 FCC verification
  • 2.15 Environmental protection
  • 2.16 Corrosive environment
• 3.0 Configuring and mounting the drive
  • 3.1 Handling and static discharge precautions
  • 3.2 Jumper settings
    • 3.2.1 Master/slave configuration
    • 3.2.2 Cable-select option
  • 3.3 Drive mounting
  • 3.4 Drive integration
    • 3.4.1 Drive installation
    • 3.4.2 Consumer usage
  • 3.5 Security Erase--ATA security commands
    • 3.5.1 Security Thaw command
    • 3.5.2 Security Erase procedure
    • 3.5.3 Drive State after security erase
• 4.0 ATA interface
  • 4.1 ATA interface signals and connector pins
    • 4.1.1 ATA interface specifications
      • 4.1.1.1 Legacy mode -- Multi-word DMA not supported
      • 4.1.1.2 Legacy mode -- Interrupts disabled mode (polling) supports limited functionality
      • 4.1.1.3 PIO Read -- Interrupts Enabled mode
      • 4.1.1.4 Device 0 only configurations
      • 4.1.1.5 48-bit (Extended mode) Sector Count register must be written twice
    • 4.1.2 ATA Security policy exceptions
    • 4.1.3 Additional technical notes
    • 4.1.4 Drive Trust Mode supported
    • 4.1.5 Full Disc Encryption support
    • 4.1.6 Supported ATA commands
    • 4.1.7 Identify Device command
    • 4.1.8 Set Features command
• 5.0 Compatibility summary
  • 5.1 Installation considerations
  • 5.2 BIOS versions tested
  • 5.3 Operating system versions tested
  • 5.4 Compatibility test configurations
  • 5.5 Software utilities
    • 5.5.1 Third party software support
• 6.0 Seagate Technology support services
  • Numerics
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • J
  • K
  • L
  • M
  • N
  • O
  • P
  • R
  • S
  • T
  • U
  • V
  • W