Document Outline

• Chapter1Overview.pdf
  • Chapter 1: Overview
    • 1.1 About the Transport GT20 B5161
    • 1.2 Features
    • 1.3 Unpacking
      • 1.3.1 Opening the Box
      • 1.3.2 Box Contents
      • 1.3.3 Accessories
        • 1 x Tyan driver CD
        • Mounting Bracket x 4
    • 1.4 About the Product
      • 1.4.1 Front View
        • CD-ROM Drive
      • 1.4.2 Rear View
        • Power Supply Socket
      • 1.4.3 LED Definition
      • 1.4.4 Internal View
      • 1.4.5 Motherboard Block Diagram
      • 1.4.6 Motherboard Layout
• Chapter2Setting Up.pdf
  • CPU socket
  • Chapter 2: Setting Up
    • 2.0.1 Before You Begin
    • 2.0.2 Work Area
    • 2.0.3 Tools
    • 2.0.4 Precautions
    • 2.1 Rack Mounting
      • 2.1.1 Installing the Server in a Rack
        • 1. Screw the mounting ear to each side of Transport GT20 as shown using 2 screws from the supplied screws kit.
        • 2. Draw out the inner rails from rail assembly. Install inner rails to left and right sides of chassis using 2 M4-5L(D) screws for each side.
        • 3. Measure the distance between inner side of the front and rear mounting brackets in the rack.
        • 4. Locate the front and rear brackets.
        • 5. Reserve 90mm for Transport GT20 on the front bracket. Secure the front bracket to outer rail with 2 M4-4L(C) screws.
        • 6. Reserve the distance same as in Step 2 on rear bracket. Secure the rear bracket to outer rail with 2 M4-4L(C) screws.
        • 7. Secure the outer rail to the rack using 2 brackets and 4 M4-8L(E) screws for each side (A). Secure the mounting brackets from inside, not outside, of the rack (B).
        • 8. Draw out the middle rail to the latch position.
        • 9. Lift the chassis and then insert the inner slide rails into the middle rails.
        • 10. Push the chassis in and press the latch key (A). Then push the whole system into the rack (B).
        • 11. Secure the mounting ears of chassis to the rack with 2 M4-15L(F) screws.
    • 2.2 Installing Motherboard Components
      • 2.2.1 Removing the Chassis Cover
        • 1. Release the screw on the back side. Then slide the chassis cover in the direction of arrow.
        • 2. Lift the cover off.
      • 2.2.2 Installing the CPU, Heatsink and Air Duct
        • 1. Release the pre-installed air duct. Locate the CPU socket.
        • 2. Remove the cover on the CPU socket.
        • 3. Locate the lever of CPU socket.
        • 4. Press and pull the lever in the direction as illustrated..
        • 5. Open the socket in the direction as illustrated.
        • 6. Place CPU on the socket, ensuring that the edge with triangle mark aims at the edge of socket with triangle mark.
        • 7. Close the cover and secure the CPU socket in the reverse procedures from step 2 to 6.
        • 8. Secure the heatsink with 4 screws. NOTE: Remember to install the washer and nut while installing the screws.
        • 9. Secure the air duct with 2 screws.
      • 2.2.3 Installing the Memory
        • 1. Locate the memory slots on the motherboard.
        • 2. Press the memory slot locking levers in the direction of the arrows as shown in the following illustration.
        • 3. Align the memory module with the slot. The module has indentations that align with notches in the slots.
        • 4. Insert the memory module into the slot as shown.
      • 2.2.4 Installing the PCI Card
        • 1. Push the tab of PCI slot on the rear panel in the direction as shown to release the bracket.
        • 2. Move the bracket to right as shown and then take off the bracket (A).
        • 3. Insert the PCI card in the directions of arrow (B).
        • 4. Push the tab of PCI slot on the rear panel in the direction as shown to fix PCI card.
    • 2.3 Installing the Hard Drive
      • 1. Press the locking lever latch in the direction of arrow (A) and then pull the locking lever open (B).
      • 2. Slide the drive tray out.
      • 3. Place a hard drive into the drive tray.
      • 4. Using 4 HDD screws to secure the HDD.
      • 5. Reinsert the drive tray into the chassis (A), ensuring that the drive tray is completely inserted into the chassis (B).
      • 6. Pressing the locking lever to secure the hard drive tray.
    • 2.4 Installing the Slim FDD (Option)
      • 1. Locate the two FDD rails and screws from the FDD kit. Secure the two rails to FDD using four screws.
      • 2. Connect the FFC cable to FDD.
      • 3. Use a screw driver to take off the door of FDD tray.
      • 4. Insert the FDD module into the tray.
      • 5. Connect the FFC cable to the FDD connector on M1012 adapter board.
      • 6. Locate the FDD cable from FDD kit. Connect the wrinkle side to the connector on M1012 adapter board. Refer to the picture below for the correct direction.
      • 7. Connect the other side to the connector on motherboard.
• Chapter3Replacing.pdf
  • Chapter 3: Replacing Pre-Installed Components
    • 3.1 Introduction
      • 3.1.1 Work Area
      • 3.1.2 Tools
      • 3.1.3 Precautions
    • 3.2 Disassembly Flowchart
    • 3.3 Removing the Cover
      • 1. Release the screw on the back side. Then slide the chassis cover in the direction of arrow.
      • 2. Lift the cover off.
    • 3.4 Replacing Motherboard Components
      • 3.4.1 Disconnecting All Motherboard Cables
        • 1. Disconnect ATX power cables
        • 2. Disconnect the Fan, Front Panel, SATA and USB cables. Refer to the mainboard layout on p.13 for the locations.
        • 3. Disconnect the PWM cable .
      • 3.4.2 Removing the Motherboard
        • 1. Release the two screws securing the link bar.
        • 2. Remove the link bar.
        • 3. Remove the eleven screws securing the motherboard to the chassis.
        • 4. Remove the motherboard.
    • 3.5 Replacing the LED Control Board
      • 1. Remove the 2 screws securing the LED control board to the chassis.
      • 2. Pull the LED control board free from the chassis and unplug the ribbon and USB cables from the connector.
      • 3. Remove the three screws securing the LED control board to the bracket
      • 4. Release the LED control board from the chassis. After replacement, insert and secure the unit to the chassis following the reverse procedures from step 1~3.
    • 3.6 Replacing the M1012 Adapter Board
      • 1. Before replacing M1012 adapter board, you must disconnect the four SATA cables connected to the SATA backplane. After that, disconnect all the cables connected to the M1012 adapter board.
      • 2. Remove the Front Panel, LAN/ID LED and Fan Tach cables.
      • 3. Remove the Front Panel Control Board cable.
      • 4. Remove one power cable connected to M1012 adapter board and two power cables connected to SATA backplane.
      • 5. Remove the 6 screws securing the M1012 adapter board. After that, you can release the M1012 adapter board from the chassis.
      • 3.6.1 M1012 Adapter Board Features
      • 3.6.2 M1012 Adapter Board Connector Pin Definition
      • 3.6.3 System Fan Layout
    • 3.7 Replacing the SATA Backplane
      • 1. After removing the M1012 adapter board, you can easily grab the two lables to lift the SATA backplane.
      • 2. Remove the ten screws that secure the bracket to the backplane.
      • 3. Release the backplane free from the bracket.
      • 4. Replace the unit to the chassis following the reverse procedures from step 1 to 3 after done.
      • 3.7.1 S-ATA Backplane (M1204) Features
    • 3.8 Replacing the Cooling Fan
      • 1. Locate the fan connector on the motherboard and unplug the fan cable.
      • 2. Take the fan away from the chassis.
      • 3. Replace the fan into the chassis following the reverse procedures from 1 to 2 after done.
    • 3.9 Replacing the Power Supply
      • 1. Remove the two screws that secure the power supply to the chassis.
      • 2. Remove the screw that secure the fan assembly to the chassis
• Appendix.pdf
  • Appendix I: BIOS Differences
  • Appendix II: Cable Connection Tables
    • Table 1: B5161G20S4H Model
    • Table 2: System Fan to M1012 Adapter Board
    • Table 3: M1012 Adapter Board to Motherboard
    • Table 4: Power Supply to Motherboard
    • Table 5: Power Supply to M1012 Adapter Board
    • Table 6: Power Supply to M1204 Backplane
    • Table 7: M1012 Adapter Board to Motherboard
    • Table 8: M1003 Front Panel Control Board Related Cable
    • Table 9: CD-ROM Related Cable
    • Table 10: Chassis Intrusion Cable
    • Table 11: FDD Related Cable (Option)
    • Technical Support
• Appendix.pdf
  • Appendix I: BIOS Differences
  • Appendix II: Cable Connection Tables
    • Table 1: B5161G20S4H Model
    • Table 2: System Fan to M1012 Adapter Board
    • Table 3: M1012 Adapter Board to Motherboard
    • Table 4: Power Supply to Motherboard
    • Table 5: Power Supply to M1012 Adapter Board
    • Table 6: Power Supply to M1204 Backplane
    • Table 7: M1012 Adapter Board to Motherboard
    • Table 8: M1003 Front Panel Control Board Related Cable
    • Table 9: CD-ROM Related Cable
    • Table 10: Chassis Intrusion Cable
    • Table 11: FDD Related Cable (Option)
    • Technical Support
• Appendix III.pdf
  • Appendix III: Installing SMDC Cards
    • Installing M3289 into HDD Tray
      • 1. Fold up the cable.
      • 2. a: Choose a HDD tray. b: Insert the cable into the rear of HDD tray. c: Pull the cable out.
      • 3. Connect the cable to M3289.
      • 4. Align M3289 in reverse with 4 “M1” stand-offs. Secure the SMDC with 4 screws as illustrated.
      • 5. Secure M3289 onto HDD tray as illustrated.
      • 6. Insert and secure the HDD tray. NOTE: For internal or dummy HDD tray, secure the HDD tray with 1 or 2 screws.
      • 7. Arrange and connect the cable to SMDC connector on mainboard. Be careful not to block the air flow.
    • Installing M3290/M3291 into HDD tray
      • 1. Secure a removable stand-off of 13.5mm to the location of “M2” stand-off as illustrated on SMDC bracket.
      • 2. Secure M3290 in reverse to 4 “M2” stand-offs on bracket.
      • 3. a: Choose a HDD tray. NOTE: Refer to the location of SMDC connector on mainboard for choosing a HDD tray. b: Secure SMDC to the HDD tray.
      • 4. a: Inset the cable into the rear of HDD tray. b: Connect the cable to M3290. c: Insert and secure HDD tray.
      • 5. Arrange and connect the cable to SMDC connector on mainboard. Be careful not to block the air flow.
    • Installing M3290/M3291 into GT24 Chassis
      • 1. Disconnect the power connectors on HDD backplane and M1010.
      • 2. Push the power cables aside.
      • 3. Align M3290 with 4 “M2” PC stand-offs. Secure M3290 to mainboard with 4 screws.
      • 4. Connect the cable to M3290. Arrange and connect the cable to SMDC connector on mainboard. Be careful not to block the air flow.
      • 5. Reconnect the power connectors on HDD backplane and M1010.
• Appendix.pdf
  • Appendix I: BIOS Differences
  • Appendix II: Cable Connection Tables
    • Table 1: B5161G20S4H Model
    • Table 2: System Fan to M1012 Adapter Board
    • Table 3: M1012 Adapter Board to Motherboard
    • Table 4: Power Supply to Motherboard
    • Table 5: Power Supply to M1012 Adapter Board
    • Table 6: Power Supply to M1204 Backplane
    • Table 7: M1012 Adapter Board to Motherboard
    • Table 8: M1003 Front Panel Control Board Related Cable
    • Table 9: CD-ROM Related Cable
    • Table 10: Chassis Intrusion Cable
    • Table 11: FDD Related Cable (Option)
• Appendix III.pdf
  • Appendix III: Installing SMDC Cards
    • Installing M3289 into HDD Tray
      • 1. Fold up the cable.
      • 2. a: Choose a HDD tray. b: Insert the cable into the rear of HDD tray. c: Pull the cable out.
      • 3. Connect the cable to M3289.
      • 4. Align M3289 in reverse with 4 “M1” stand-offs. Secure the SMDC with 4 screws as illustrated.
      • 5. Secure M3289 onto HDD tray as illustrated.
      • 6. Insert and secure the HDD tray. NOTE: For internal or dummy HDD tray, secure the HDD tray with 1 or 2 screws.
      • 7. Arrange and connect the cable to SMDC connector on mainboard. Be careful not to block the air flow.
    • Installing M3290/M3291 into HDD tray
      • 1. Secure a removable stand-off of 13.5mm to the location of “M2” stand-off as illustrated on SMDC bracket.
      • 2. Secure M3290 in reverse to 4 “M2” stand-offs on bracket.
      • 3. a: Choose a HDD tray. NOTE: Refer to the location of SMDC connector on mainboard for choosing a HDD tray. b: Secure SMDC to the HDD tray.
      • 4. a: Inset the cable into the rear of HDD tray. b: Connect the cable to M3290. c: Insert and secure HDD tray.
      • 5. Arrange and connect the cable to SMDC connector on mainboard. Be careful not to block the air flow.
    • Installing M3290/M3291 into GT24 Chassis
      • 1. Disconnect the power connectors on HDD backplane and M1010.
      • 2. Push the power cables aside.
      • 3. Align M3290 with 4 “M2” PC stand-offs. Secure M3290 to mainboard with 4 screws.
      • 4. Connect the cable to M3290. Arrange and connect the cable to SMDC connector on mainboard. Be careful not to block the air flow.
      • 5. Reconnect the power connectors on HDD backplane and M1010.
• Appendix III.pdf
  • Appendix III: Installing SMDC Cards
    • Installing M3289 into HDD Tray
      • 1. Fold up the cable.
      • 2. a: Choose a HDD tray. b: Insert the cable into the rear of HDD tray. c: Pull the cable out.
      • 3. Connect the cable to M3289.
      • 4. Align M3289 in reverse with 4 “M1” stand-offs. Secure the SMDC with 4 screws as illustrated.
      • 5. Secure M3289 onto HDD tray as illustrated.
      • 6. Insert and secure the HDD tray. NOTE: For internal or dummy HDD tray, secure the HDD tray with 1 or 2 screws.
      • 7. Arrange and connect the cable to SMDC connector on mainboard. Be careful not to block the air flow.
    • Installing M3290/M3291 into HDD tray
      • 1. Secure a removable stand-off of 13.5mm to the location of “M2” stand-off as illustrated on SMDC bracket.
      • 2. Secure M3290 in reverse to 4 “M2” stand-offs on bracket.
      • 3. a: Choose a HDD tray. NOTE: Refer to the location of SMDC connector on mainboard for choosing a HDD tray. b: Secure SMDC to the HDD tray.
      • 4. a: Inset the cable into the rear of HDD tray. b: Connect the cable to M3290. c: Insert and secure HDD tray.
      • 5. Arrange and connect the cable to SMDC connector on mainboard. Be careful not to block the air flow.
    • Installing M3290/M3291 into GT24 Chassis
      • 1. Disconnect the power connectors on HDD backplane and M1010.
      • 2. Push the power cables aside.
      • 3. Align M3290 with 4 “M2” PC stand-offs. Secure M3290 to mainboard with 4 screws.
      • 4. Connect the cable to M3290. Arrange and connect the cable to SMDC connector on mainboard. Be careful not to block the air flow.
      • 5. Reconnect the power connectors on HDD backplane and M1010.
      • Technical Support