Document Outline

• PJ510_UGTOC.pdf
  • Contents
• PJ510_UG.pdf
  • For Your Records
  • Features
    • Projector Features
      • Ultra High Brightness
      • Partial Magnification Function
      • Keystone Distortion Correction
      • Whisper Mode Equipped
      • NOTE:
        • Projector
        • with Lens Cap
      • NOTE:
      • WARNING:
  • Part Names
    • The Projector
      • Projector (Front/Right)
      • Fastening The Lens Cap
        • 1 Fix the strap to the strap ring of lens cap, as the right drawing.
        • 2 Put one piece of the strap into the groove on rivet, as the right drawing.
        • 3 Push the rivet into the strap hole.
      • Projector (Rear/Left)
    • The Remote Control
  • Setting Up
    • Arrangement
      • Reference for the 4:3 aspect ratio
      • Reference for the 16:9 aspect ratio
    • Adjusting The Projector’s Elevator
      • 1 Press and hold in the elevator buttons.
    • Connecting Your Devices
      • NOTE:
      • About Plug-and-Play Capability
      • NOTE:
      • Connecting to a computer
      • If using a SCART RGB input,
      • Connecting to a DVD/VCR player
    • Connecting Power Supply
      • 1 Connect the connector of the power cord to the AC inlet of the projector.
      • 2 Firmly plug the power cord’s plug into the outlet.
  • Remote Control
    • Putting Batteries
      • 1 Remove the battery cover.
      • 2 Insert the batteries.
      • 3 Close the battery cover.
    • Operating The Remote Control
  • Power ON/OFF
    • Turning On The Power
      • NOTE:
        • 1 Make sure that the power cord is firmly and correctly connected to the projector and outlet.
        • 2 When the lens cap is attached, remove the lens cap.
        • 3 Set the power switch to [ | ] (ON).
        • 4 Press the STANDBY/ON button of the projector or the remote control.
    • Selecting An Input Signal
      • 1 Using the projector’s control button
      • Press the INPUT button.
      • Selecting a RGB signal, using the remote control
      • Press the RGB button.
      • Selecting a video signal, using the remote control
      • Press the VIDEO button.
        • 2 Use the zoom ring to adjust the screen size.
        • 3 Use the focus ring to focus the picture.
    • Turning Off The Power
      • NOTE:
        • 1 Press the STANDBY/ON button of the projector or the remote control.
        • 2 Press the STANDBY/ON button again while “Power off?” the message is visible.
        • 3 Switch the power switch to [O] (OFF).
        • 4 Attach the lens cap.
  • Operating
    • Adjusting The Volume
      • 1 Press the VOLUME button.
      • 2 Use the (p), (q) buttons to adjust the volume.
    • Temporarily Muting The Sound
      • 1 Press the MUTE button.
    • Adjusting The Position
      • 1 Press the POSITION button.
      • 2 Use the (t), (u), (p), (q) buttons to adjust the position.
      • NOTE:
    • Using The Automatic Adjustment Feature
      • 1 Press the AUTO button.
      • NOTE:
    • Correcting Keystone Distortions
      • 1 Press the KEYSTONE button.
      • 2 Use the (p), (q) buttons to correct distortion
      • NOTE:
    • Using The Magnify Feature
      • 1 Press the MAGNIFY (ON) button
    • Freezing The Screen
      • 1 Press the FREEZE button
      • NOTE:
    • Signal Searching
      • 1 Press the SEARCH button
      • NOTE:
    • Selecting The Aspect Ratio
      • 1 Press the ASPECT button
    • Temporarily Blanking The Screen
      • 1 Press the BLANK button
      • NOTE:
  • Multifunctional Settings
    • Using The Menu Functions
      • 1 Press the MENU button.
      • 2 Use the (p), (q) buttons to select a menu, then press the (u) or ENTER button.
      • 3 Use the (p), (q) buttons to select an item, then press the (u) or ENTER button.
      • 4 Use the (p), (q) buttons to operate the item.
      • [ex. Adjusting VOLUME]
    • MAIN Menu
    • PICTURE-1 Menu
    • PICTURE-2 Menu
    • INPUT Menu
    • AUTO Menu
    • SCREEN Menu
    • OPTION Menu
  • Lamp
    • Replacing The Lamp
      • 1 Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 45 minutes.
  • Air Filter
    • Caring For The Air Filter
      • 1 Turn off the projector, and unplug the power cord.
      • 2 Apply a vacuum cleaner to the top of the filter cover to clean the air filter.
      • 3 Reset the filter timer, according to following “Reset The Filter Timer”.
    • Replacing The Air Filter
      • 1 Turn off the projector, and unplug the power cord.
      • 2 Contact your local dealer to prepare a new air filter. Tell the dealer your air filter type number.
  • Other Care
    • Caring For The Inside Of The Projector
    • Caring For The Lens
      • 1 Turn off the projector, and unplug the power cord.
      • 2 Lightly wipe the lens with a commercially available lens- cleaning wipe. Do not touch the lens directly with your hand.
    • Caring For The Cabinet And Remote Control
      • 1 Turn off the projector, and unplug the power cord.
  • Troubleshooting
    • Related Messages
      • TO MAXIMIZE PERFORMANCE, LAMP REPLACEMENT IS RECOMMENDED.
    • Regarding The Indicator Lamps
      • POWER indicator
      • LAMP indicator
      • TEMP indicator
      • Description
      • Lighting in orange
      • Turned off
      • Turned off
      • The unit is in a standby state. Please refer to the “Power ON/OFF” section of this manual.
      • Flashing in green
      • Turned off
      • Turned off
      • The unit is warming up. Please wait.
      • Lighting in green
      • Turned off
      • Turned off
      • The unit is in an ON state. Ordinary operations may be performed.
      • Flashing in orange
      • Turned off
      • Turned off
      • The unit is cooling down. Please wait.
      • Blinking in red
      • -
      • -
    • Phenomena That May Easily Be Mistaken For Machine Defects
      • NOTE:
        • Phenomenon
        • Cases not involving a machine defect, and Items to be confirmed
        • Power does not come ON.
        • The main power source is not ON.
        • Turn on the main power.
        • The electrical power cord is not plugged in.
        • Correctly connect the power cord.
        • The main power source has been interrupted during operation, such as by a power outage (blackout), etc.
    • Warranty And After-Service
  • Specifications
    • Product name
    • Liquid crystal panel
    • Panel size
    • Drive system
    • Pixels
    • NOTE:
  • Customer Support
  • LIMITED WARRANTY
    • VIEWSONIC Projector
  • Appendix
    • Power Cord Safety Guidelines
      • USA UL
      • Canada CSA
      • Germany VDE
      • Switzerland SEV
      • Britain BASE/BS
      • Japan Electric Appliance Control Act
      • AC PLUG CORD PRECAUTIONS FOR THE UNITED KINGDOM
      • FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
      • IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET THEN THE PLUG SHOULD BE CUT OFF AND DISPOSED OF SAFELY.
      • THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO AN APPROPRIATE SOCKET.
      • If a new plug is to be fitted, please observe the wiring code as shown below.
      • If in any doubt, please consult a qualified electrician.
      • WARNING: THIS APPLIANCE MUST BE EARTHED.
      • IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
      • Green-and-Yellow: Earth
      • Blue: Neutral
      • Brown: Live
    • Compliance Information for U.S.A.
    • Compliance Information for Canada
    • Compliance Information for European Countries
      • CE Conformity
    • User Information for all Countries