Document Outline

• Table of Contents
  • Read This First
  • Product Safety
  • FCC and CDC Regulatory Statements
  • Chapter 1. Introduction
    • SCON-20L/22L General Description
    • SCON-20L/22L Hardware Components
  • Chapter 2. Installation
    • Installation Checklist
    • Printed Circuit
    • Unpacking Additional Printed Circuit Boards (PCBs)
    • Installing/Removing Printed Circuit Boards (PCBs) - by Authorized Service Personnel Only
    • Location Planning for the SCON-20L/22L
    • Environmental Parameters
    • Power Requirements
    • Supplied Cable Distance
    • Power Cable Requirements
    • Connections
    • ESCON Channel Interface
    • Indicators, Switches and Connectors
    • Attaching the ESC Interface to the Channel
    • 10/100 Mbps Fast Ethernet (FET)
    • LED Descriptions
    • Coax Device Attachment
    • Dynamic Multiplexing
    • Device Attachment
  • Chapter 3. Board Population
    • Introduction
    • Printed Circuit Board Names
    • Slot Population and Identification
    • Physical Slot Identification
    • Slot Numbers and Logical Identifiers
    • Board ID Assignments
  • Chapter 4. Operation
    • Indicators
    • Operator Panel LEDs
    • Power Switch
    • Keypad
    • Copy Systems Disks
    • IML Procedure
    • Error Types
    • IML Errors (ERR ___)
    • Exception Errors (XCP ___)
    • Hardware Failures (FAIL ___)
    • Online Errors
    • Error Indicators
    • Event Log
    • Status Line of Attached Terminal
    • Operator Panel Display
    • Operator Panel Check Light
    • Software Merge
    • Warning Messages
    • Failure Messages
  • Chapter 5. Assembly Installation/Removal/Replacement
    • Introduction
    • Assembly Drawing
    • Replaceable Assemblies
    • Covers
    • Circuit Board Assembly
    • Power Supply Assembly
    • Operator Panel
    • Floppy Disk Drive
    • Mother Board Assembly
    • New Hardware Installation Procedures
    • Second CDA Installation (SCON-22L Only)
    • Installation of FET Board
  • Index
    • Symbols
      • 10/100 Mbps Fast Ethernet (FET)
    • A
      • Attaching the ESC Interface to the Channel
    • B
      • Board ID Assignments
    • C
      • Coax Device Cables
      • Coax Ports
      • Connectors
      • Copy Systems Disks
    • D
      • Debug SW
    • E
      • Environmental Parameters
      • Error Types
      • ESCON
        • Channel Interface
        • Fiber Optic Cable
    • F
      • Failure Messages
      • FET Board Installation
      • Floppy Disk Drive
    • H
      • Hard Disk Drive
    • I
      • IML Procedure
      • Indicators
        • ACTV (green)
        • FAIL/ERR (amber)
        • IRQ (amber)
        • ONLN (green)
      • Installation Procedures,
        • FET Board
        • Second CDA
      • Installation Task Checklist
      • Installing/Removing Printed Circuit Boards
    • K
      • Keypad
    • L
      • LED Descriptions
      • Logical Identifiers
    • M
      • Mother Board Assembly
    • N
      • New Hardware Installation Procedures
    • O
      • Operator Panel LEDs
        • Check
        • Config
        • Diag
        • HD-Act
        • IML
        • Power
      • Optional Hardware Features
    • P
      • Power Cable
      • Power Cable Requirements
      • Power Requirements
      • Power Supply Assembly
      • Power Switch
      • Printed Circuit Board Names
        • CDA
        • ESC
        • FET
    • R
      • Replaceable Assemblies
      • RJ-45 Connector Pin Assignments
    • S
      • SCON-20L/22L
        • General Description
        • Hardware Components
      • Second CDA Installation
      • Slot Identification
      • Slot Numbers
      • Slot Population
      • Software Merge
      • Switches
    • U
      • Unpacking Printed Circuit Boards
    • W
      • Warning Messages