Document Outline

• TITLE
• TABLE OF CONTENTS
• 1.0 INTRODUCTION
• 2.0 SPECIFICATIONS
  • 2.1 Analog Inputs
  • 2.2 Control Capability
  • 2.3 Digital Outputs
  • 2.4 Digital Inputs
  • 2.5 Serial Interface
  • 2.6 Power Supply
• 3.0 INSTALLATION
  • 3.1 PHYSICAL CONSIDERATIONS
    • 3.1.1 MOUNTING
    • 3.1.2 EXTERNAL WIRING
    • 3.1.3 GENERAL WIRING REQUIREMENTS
    • 3.1.4 RECOMMENDED CABLES P/N
    • 3.1.5 NOISE SUPPRESSION FOR DIGITAL OUTPUTS
  • 3.2 TERMINAL BLOCK AND CONNECTOR LAYOUT
  • 3.3 ANALOG INPUTS
    • 3.3.1COMMON MODE VOLTAGE
    • 3.3.2NORMAL MODE VOLTAGE
    • 3.3.3GROUNDING
    • 3.3.4 SOURCE IMPEDANCE
    • 3.3.5 INPUT SCALING
    • 3.3.6 VOLTAGE INPUTS
    • 3.3.7MILLIAMP INPUTS
    • 3.3.8THERMOCOUPLE INPUTS
    • 3.3.9RTD INPUTS
    • 3.3.10 INFRARED NON-CONTACT TEMPERATURE SENSORS
    • 3.3.11 SCALING AND CALIBRATION
    • 3.3.12 DIAGRAMS OF TYPICAL INPUTS
  • 3.4 CONTROL OUTPUTS
    • 3.4.1 PID CONTROL AND ALARM OUTPUTS CONNECTIONS
    • 3.4.2 PID OUTPUT LIMITING
  • 3.5 COMPUTER SERIAL COMMUNICATIONS
    • 3.5.1 RS-232 CONNECTIONS
    • 3.5.2 OTHER RS-232 LINES
    • 3.5.3 RS-485 DESCRIPTION
• 4.0 FRONT PANEL OPERATION AND DISPLAYS
  • 4.1 FRONT PANEL KEYS
  • 4.2 DISPLAYS
    • 4.2.1 BAR GRAPH DISPLAY
    • 4.2.2 SINGLE LOOP DISPLAY
    • 4.2.3 SCANNING DISPLAY
    • 4.2.4 ALARM DISPLAY
  • 4.3 GENERAL PROGRAMMING AND EDITING
  • 4.4 OPERATIONAL MENUS
    • 4.4.1 CHANGE SETPOINT
    • 4.4.2 SET LOOP TO MANUAL/AUTO
    • 4.4.3 ADJUSTING OUTPUT LEVELS MANUALLY
  • 4.5 SETUP MENUS
    • 4.5.1 SETUP GLOBAL PARAMETERS?
    • 4.5.2 SETUP LOOP INPUT
    • 4.5.3 SETUP LOOP CONTROL PARAMETERS
    • 4.5.4 SETUP LOOP OUTPUTS
    • 4.5.5 SETUP ALARMS
    • 4.5.6 MANUAL I/O TEST
  • 4.6 RAMP AND SOAK OPTION
    • 4.6.1 DESCRIPTION
    • 4.6.2 RAMP/SOAK FRONT PANEL DISPLAY
    • 4.6.3 PROFILE STATUS DISPLAY
    • 4.6.4 PROFILE SELECTION MENU
    • 4.6.5 PROFILE TIME DISPLAY
    • 4.6.6 CYCLE COUNT DISPLAY
    • 4.6.7 PROFILE OPERATION MENU
    • 4.6.8 RESET PROFILE
  • 4.7 SETUP RAMP/SOAK PROFILE
    • 4.7.1 SELECT A PROFILE FOR EDITING
    • 4.7.2 COPY ANOTHER PROFILE
    • 4.7.3 EDIT TOLERANCE ALARM TIME
    • 4.7.4 EDIT READY SETPOINT
    • 4.7.5 EDIT READY EVENT STATES
    • 4.7.6 EDIT EXTERNAL RESET
    • 4.7.7 EDIT SEGMENT NUMBER
    • 4.7.8 EDIT SEGMENT TIME
    • 4.7.9 EDIT SEGMENT SETPOINT
    • 4.7.10 EDIT SEGMENT EVENTS
    • 4.7.11 EDIT EVENT OUTPUT NUMBER
    • 4.7.12 EDIT EVENT OUTPUT STATE
    • 4.7.13 EDIT SEGMENT TRIGGERS
• 5.0 PID CONTROL
  • 5.1 CONTROL MODES
    • 5.1.1 REVERSE-DIRECT ACTION
    • 5.1.2 HEAT/COOL DUAL OUTPUTS
    • 5.1.3 CONTROL OUTPUTS
    • 5.1.4 DIGITAL OUTPUT
    • 5.1.5 DISTRIBUTED ZERO CROSSING
  • 5.2 TUNING PID LOOPS
    • 5.2.1 PROPORTIONAL CONTROL:
    • 5.2.2 PROPORTIONAL WITH INTEGRAL CONTROL:
    • 5.2.3 PROPORTIONAL W/ INTEGRAL W/ DERIVATIVE CONTROL:
    • 5.2.4 OUTPUT DIGITAL FILTER:
    • 5.2.5 PID TUNING CONSTANTS
    • 5.2.6 GENERAL PID CONSTANTS BY APPLICATION
• 6.0 SOFTWARE
  • 6.1 ANASOFT
  • 6.2 CUSTOM APPLICATION PROGRAMS
• 7.0 TROUBLE SHOOTING INFORMATION
  • 7.1 Stand Alone Systems
    • 7.1.1 Checking Control Outputs
    • 7.1.2 Checking Digital I/O
  • 7.2 Computer Supervised Systems
    • 7.2.1 Computer Problems
    • 7.2.2 Computer Software
    • 7.2.3 User Written Software
    • 7.2.4 ANASOFT
    • 7.2.5 Communications Problems
    • 7.2.6 Serial Interface
• 8.0 SOFTWARE COMMAND STRUCTURE
• 9.0 GLOSSARY OF TERMS