Document Outline

• Front Cover
• Table of Contents
• i Preface & General Safety
  • i.1 Preface
    • Applicable Documentation
    • Symbols
    • Terms and Abbreviations
  • i.2 General Safety
    • Supplemental Safety Information
    • Safety Messages
    • Drive Label Warnings
    • Warranty Information
    • Quick Reference
• 1 Receiving
  • 1.1 Section Safety
  • 1.2 Model Number and Nameplate Check
    • Nameplate
  • 1.3 Component Names
    • IP20/Open-Chassis
    • Front Views
• 2 Mechanical Installation
  • 2.1 Section Safety
  • 2.2 Mechanical Installation
    • Installation Environment
    • Installation Orientation and Spacing
    • Exterior and Mounting Dimensions
• 3 Electrical Installation
  • 3.1 Section Safety
  • 3.2 Standard Connection Diagram
  • 3.3 Main Circuit Connection Diagram
    • Single-Phase 200 V Class Models BA0001 to BA0010
    • Three-Phase 200 V Class Models 2A0001 to 2A0020 Three-Phase 400 V Class Models 4A0001 to 4A0011
  • 3.4 Terminal Block Configuration
  • 3.5 Protective Covers
    • IP20/Open-Chassis Cover Removal and Installation
  • 3.6 Main Circuit Wiring
    • Main Circuit Terminal Functions
    • Wire Gauges and Tightening Torques
    • Main Circuit Terminal Power Supply and Motor Wiring
  • 3.7 Control Circuit Wiring
    • Control Circuit Terminal Block Functions
    • Terminal Configuration
    • Wiring Procedure
  • 3.8 I/O Connections
    • Sinking/Sourcing Mode Switch
  • 3.9 Main Frequency Reference
    • DIP Switch S1 Analog Input Signal Selection
  • 3.10 Braking Resistor
    • Installation
  • 3.11 Interlocking with Connected Machinery
    • Drive Ready Signal
  • 3.12 Wiring Checklist
• 4 Start-Up Programming & Operation
  • 4.1 Section Safety
  • 4.2 Using the Digital LED Operator
    • Keys, Displays, and LEDs
    • Digital Text Display
    • LED Screen Displays
    • LO/RE LED and RUN LED Indications
    • Menu Structure for Digital LED Operator
  • 4.3 The Drive and Programming Modes
    • Navigating the Drive and Programming Modes
    • Changing Parameter Settings or Values
    • Verifying Parameter Changes: Verify Menu
    • Switching Between LOCAL and REMOTE
    • Parameters Available in the Setup Group
  • 4.4 Start-up Flowchart
    • Flowchart: Basic Start-up
  • 4.5 Basic Operation
    • Initialize Parameter Values: A1-03
    • Frequency Reference Source: b1-01
    • Run Command Input Selection: b1-02
    • Stopping Method Selection: b1-03
    • Acceleration/Deceleration: C1-01 to C1-04
    • Drive Duty and Carrier Frequency Selection: C6-01 and C6-02
    • Multi-Step Speed Operation (4-Step Speed)
    • E1: V/f Characteristics
    • Motor Parameters: E2-01 to E2-03
    • Digital Output: H2-01
    • Analog Outputs: H4-01 to H4-03
    • Motor Protection: L1-01 and L1-02
    • Drive Status Monitors: U1-01 to U4-13
  • 4.6 Powering Up the Drive
    • Powering Up the Drive and Operation Status Display
    • V/f Pattern Setting
  • 4.7 No-Load Operation Test Run
    • No-Load Operation Test Run
  • 4.8 Test Run with Load Connected
    • Test Run with the Load Connected
  • 4.9 Verifying and Backing Up Parameter Settings
    • Parameter Access Level: A1-01
    • Password Settings: A1-04, A1-05
    • Copy Function (Optional)
  • 4.10 Test Run Checklist
• 5 Troubleshooting
  • 5.1 Section Safety
  • 5.2 Motor Performance Fine Tuning
    • Parameters for Tuning the Drive
    • Motor Hunting and Oscillation Control Parameters
  • 5.3 Drive Alarms, Faults, and Errors
    • Types of Alarms, Faults, and Errors
    • Alarm and Error Displays
  • 5.4 Fault Detection
    • Fault Displays, Causes, and Possible Solutions
  • 5.5 Alarm Detection
    • Alarm Codes, Causes, and Possible Solutions
  • 5.6 Operator Programming Errors
    • oPE Codes, Causes, and Possible Solutions
  • 5.7 Diagnosing and Resetting Faults
    • Fault Occurs Simultaneously with Power Loss
    • If the Drive Still has Power After a Fault Occurs
    • Viewing Fault History Data After Fault
    • Fault Reset Methods
  • 5.8 Troubleshooting without Fault Display
    • Cannot Change Parameter Settings
    • Motor Does Not Rotate Properly after Pressing RUN Button or after Entering External Run Command
• 6 Periodic Inspection & Maintenance
  • 6.1 Section Safety
  • 6.2 Inspection
    • Recommended Daily Inspection
    • Recommended Periodic Inspection
  • 6.3 Periodic Maintenance
    • Replacement Parts
  • 6.4 Drive Cooling Fans
    • Number of Cooling Fans
    • Cooling Fan Replacement
• 7 Peripheral Devices & Options
  • 7.1 Section Safety
  • 7.2 Drive Options and Peripheral Devices
  • 7.3 Connecting Peripheral Devices
  • 7.4 Installing Peripheral Devices
    • Installing a Molded Case Circuit Breaker (MCCB) and Earth Leakage Circuit Breaker (ELCB)
    • Application Precautions when Installing a GFCI
    • Installing a Magnetic Contactor
    • Connecting an AC Reactor or DC Link Choke
    • Connecting a Surge Suppressor
    • Connecting a Noise Filter
    • EMC Filter Installation
    • Zero-Phase Reactor
    • Installing Fuses on the Input Side
    • Attachment for External Heatsink
    • Noise Filter Installation
    • Installing a Motor Thermal Overload (oL) Relay on the Drive Output
    • NEMA Type 1 Kit
  • 7.5 Options
    • Interface Options
    • Other Options
• Appendix: A Specifications
  • A.1 Heavy Duty and Normal Duty Ratings
  • A.2 Single/Three-Phase 200 V Class Drives
  • A.3 Three-Phase 400 V Class Drives
  • A.4 Drive Specifications
  • A.5 Drive Watt Loss Data
  • A.6 Drive Derating Data
    • Temperature Derating
    • Altitude Derating
• Appendix: B Parameter List
  • B.1 Parameter Groups
  • B.2 Parameter Table
    • A: Initialization Parameters
    • b: Application
    • C: Tuning
    • d: References
    • E: Motor Parameters
    • H Parameters: Multi-Function Terminals
    • L: Protection Function
    • n: Advanced Performance Set-Up
    • o: Operator Related Parameters
    • U: Monitors
  • B.3 Defaults by Drive Model and Duty Rating ND/HD
• Appendix: C Standards Compliance
  • C.1 Section Safety
  • C.2 European Standards
    • CE Low Voltage Directive Compliance
    • EMC Guidelines Compliance
  • C.3 UL Standards
    • UL Standards Compliance
    • Drive Motor Overload Protection
• Index
  • Numerics
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • J
  • L
  • M
  • N
  • O
  • P
  • R
  • S
  • T
  • U
  • V
  • W
  • Z
• Revision History
• Back Cover