Document Outline

• Front Cover
• Table of Contents
• i Preface & General Safety
  • i.1 Preface
    • Applicable Documentation
    • Symbols
    • Terms and Abbreviations
  • i.2 General Safety
    • Supplemental Safety Information
    • Safety Messages
    • Drive Label Warnings
  • i.3 Application Precautions
    • General Application Precautions
    • Installation Environment
    • Settings
    • General Handling
    • Notes on Motor Operation
• 1 Receiving
  • 1.1 Model Number and Nameplate Check
    • Nameplate
  • 1.2 Component Names
    • IP20/Open-Chassis
    • IP00/Open-Chassis
    • IP20/NEMA Type 1 Enclosure
    • Front Views
• 2 Mechanical Installation
  • 2.1 Mechanical Installation
    • Installation Environment
    • Installation Orientation and Spacing
    • Exterior and Mounting Dimensions
• 3 Electrical Installation
  • 3.1 Standard Connection Diagram
  • 3.2 Terminal Block Configuration
  • 3.3 Protective Covers
    • IP20/Open-Chassis Front and Bottom Cover Removal and Installation
    • IP20/NEMA Type 1 Front and Bottom Cover Removal and Installation
    • IP20/NEMA Type 1 Top Cover Removal and Installation
  • 3.4 Main Circuit Wiring
    • Main Circuit Terminal Functions
    • Wire Gauges and Tightening Torques
    • Main Circuit Terminal Power Supply and Motor Wiring
  • 3.5 Control Circuit Wiring
    • Control Circuit Terminal Block Functions
    • Terminal Configuration
    • Wiring Procedure
  • 3.6 I/O Connections
    • Sinking/Sourcing Mode Switch
  • 3.7 Main Frequency Reference
    • DIP Switch S1 Analog Input Signal Selection
  • 3.8 Wiring Checklist
• 4 Start-Up Programming & Operation
  • 4.1 Using the Digital LED Operator
    • Keys, Displays, and LEDs
    • LED Screen Displays
    • LO/RE LED and RUN LED Indications
    • Menu Structure for Digital LED Operator
  • 4.2 The Drive and Programming Modes
    • Changing Parameter Settings or Values
    • Switching Between LOCAL and REMOTE
    • Parameters Available in the Setup Group
  • 4.3 Start-up Flowcharts
    • Flowchart A: Basic Start-up and Motor Tuning
    • Subchart A1: Simple Motor Setup with Energy Savings or Speed Search Using V/f Mode
    • Subchart A2: High Performance Operation Using Open Loop Vector Motor Control
    • Subchart A3: Operation with Permanent Magnet Motors
  • 4.4 Powering Up the Drive
    • Powering Up the Drive and Operation Status Display
  • 4.5 Application Selection
    • Setting 1: Water Supply Pump Application
    • Setting 2: Conveyor Application
    • Setting 3: Exhaust Fan Application
    • Setting 4: HVAC Fan Application
    • Setting 5: Compressor Application
    • Setting 6: Preset 6
    • Notes on Controlling the Brake when Using Application Preset 6
    • Setting 7: Preset 7
    • Setting 8: Conveyor Application 2
  • 4.6 Basic Drive Setup Adjustments
    • Control Mode Selection: A1-02
    • Initialize Parameter Values: A1-03
    • Frequency Reference Source: b1-01
    • Run Command Input Selection: b1-02
    • Drive Duty Selection and Carrier Frequency Selection: C6-01 and C6-02
    • Drive Input Voltage Setting: E1-01
  • 4.7 Auto-Tuning
    • Types of Auto-Tuning
    • Before Auto-Tuning the Drive
    • Auto-Tuning Interruption and Fault Codes
    • Performing Auto-Tuning
    • Auto-Tuning Example
    • Input Data for Auto-Tuning
  • 4.8 No-Load Operation Test Run
    • No-Load Operation Test Run
  • 4.9 Test Run with Load Connected
    • Test Run with the Load Connected
  • 4.10 Test Run Checklist
• 5 Troubleshooting
  • 5.1 Drive Alarms, Faults, and Errors
    • Types of Alarms, Faults, and Errors
  • 5.2 Fault Detection
    • Fault Displays, Causes, and Possible Solutions
  • 5.3 Alarm Detection
    • Alarm Codes, Causes, and Possible Solutions
  • 5.4 Operator Programming Errors
    • oPE Codes, Causes, and Possible Solutions
  • 5.5 Auto‑Tuning Fault Detection
    • Auto‑Tuning Codes, Causes, and Possible Solutions
  • 5.6 Diagnosing and Resetting Faults
    • Fault Reset Methods
• Appendix: A Specifications
  • A.1 Heavy Duty and Normal Duty Ratings
  • A.2 Single/Three-Phase 200 V Class Drives
  • A.3 Three-Phase 400 V Class Drives
  • A.4 Drive Specifications
• Appendix: B Parameter List
  • B.1 Parameter Table
• Appendix: C Standards Compliance
  • C.1 European Standards
    • CE Low Voltage Directive Compliance
    • EMC Guidelines Compliance
  • C.2 UL and CSA Standards
    • UL Standards Compliance
    • CSA Standards Compliance
    • Drive Motor Overload Protection
  • C.3 Safe Disable Input Precautions
    • Safe Disable Function Description
    • Installation
  • C.4 V1000 - ORIENTAÇÃO BÁSICA
    • INVERSORES - V1000 TERMO DE GARANTIA
    • INVERSORES DE FREQUÊNCIA - V1000
• Revision History
• Back Cover