haier HWM65-828 - Manual (Page 3)

1
Meaning and description of the symbols
Contents marked with that symbol are actions forbidden
to perform. Performing of those actions may result in damage of
the machine or influence the personal safety of the user..
Contents marked with that symbol are related to the
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.otherwise
it may cause damage of the machine or injure the personal
safety of the user.
Names of the parts
Warning sign
Forbidden sign
Phenomena The reason How to settle
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are
not breakdowns sometimes.Please confirm again before sending it to repair. If there are real
breakdowns, please come to the special maintenance department or after-sale service department
of our company. Do not repair it by yourself..
The digitron displays E0.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
The water filling does not work,
the digital displays E4.
The drainage cannot work, or is too slow.
The digitron displays E1.
It stops running in midway. The digitron
displays E2.
The top lid is not closed.
The top lid is opened during reserve procedure.
Close the top lid.
Close the top lid.
Is the drain hose put down?
Is the drain hose blocked? Put down the drain hose. Open and close the top lid once.
Clean the foreign material. Open and close The top Lid Once.
Are the laundries put slantingly?
Is the machine slanting? Reorder the laundries. Close the top lid.
The machine will start running after 10
seconds of being placed horizontally.
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low? Open the water tap.
Clean the water inlet valve.
Use until
the water pressure is normal.
Open and close the
top lid once.
Open and close
the top lid once.
Open and close the top lid once.
The water level sensor is bad. Please contact the after-sales
service department. The digitron displays E6.
The machine does
not act
Not wash
Not spin
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position? Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat? Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
There's abnormal sound
inside the machine
The water tap leaks
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials. Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
Is the screw of the jointer of water
inlet hose loose or awry?
Fasten the screw of the jointer properly.
Common phenomena
Phenomena Explanation
Balance the laundries to avoid slanting.
The cloth sensor is checking the cloth, it will add water after 48 seconds.
The program is setting the drain time. Some time is needed
before it starts spinning.
The spinning is intermittent when it starts.
The wash procedure is paused.
The pulsator pauses during water inlet
in wash and rinse.
There may be some water flowing out of the
drain hose in the first use of the machine.
Push the PROGRAM button to select SPIN,
but it doesn't work.
It is to avoid splashing during water inlet.
It is the water remained in the factory inspection of performance.
Top lid component
Control panel seat Screw cover
Inner cover
Detergent box
Outer tub cover
Balance ring
Inner tub
Lint filter Pulsator
Cabinet
Adjustable foot
Back cover
Power cord
Water inlet valve
Water absorption gasket
Hook
Cabinet handle
Drain hose
Base frame
Attach block
Adjustable foot label
Filter cover
Drain bushing
Fixed foot(3)
Drain protective lid
Soften inlet