Fostex VF160EX - Manual (Page 19)

19
Top Panel
Recorder Section
25. [INPUT SEL] Key
* Set whether to send the A to H input signals [INPUT]
or track 9-16 play [TRACK] sounds to the faders of
channel faders 9 to 16.
* When executing DIRECT recording, with the [SHIFT] key
pressed down, each time the [INPUT SEL] key is pressed
while in the normal display mode, the input monitor
(READY) can be switched ON/OFF for all tracks (1-16).
However, any track that is setup to [IN] (Input) by the
INPUT SEL setting ([IN]-[TRK]) cannot be changed to
input monitor.
26. [REC ASSIGN-BUSS-SOURCE] Key
* Select the channel (SOURCE) to send to the REC BUSS
during “BUSS” recording. Select the SOURCE channel
with the [CH STATUS/CH SEL] key.
* This key lights ON when the SOURCE is selected.
27. [REC ASSIGN-BUSS-REC TRK] Key
* The track (READY) to record in “BUSS” recording is
selectable when this key is flashing. Set READY track
with the [CH STATUS/CH SEL] Key.
* This key lights ON when the READY track is set for
“BUSS” recording.
28. [REC ASSIGN-DIRECT-REC TRK] Key
* The track (READY) record in “DIRECT” recording is
selectable when this key is flashing. Set READY track
with the [CH STATUS/CH SEL] key.
* This key lights ON when the READY track is set for
“DIRECT” recording.
29. [DISP SEL/TIMEBASE] Key
* This key is used to alternate the menu shown on the
LCD in the following order.
* The tracks recorded vary, as shown below, according
to the connection jack.
a. Current location of TIME BASE selected
Shows the current location of the sound.
b. REMAINING TIME BASE Selected (time remaining)
Shows the time remaining and space available on the
disk for recordings (in terms of mono track).
c. MTC Time Input
Shows the MTC time input in the [MIDI IN] jack.
This is a convenience for operations as a slave device.
* The user can switch between time bases, as shown
below, by pressing the [DISP SEL/TIME BASE] key,
while the [SHIFT] key is depressed.
a. ABS (Absolute Time) Indication
An absolute time base from 00H 00M 00S (ABS 0) to
24H 00M 00S.
b. BAR/BEAT/CLK (Bar)
The “Bar, Beat, Clock” of the beat and tempo set with
the internal tempo map.
c. MTC (MIDI Time Code)
Display of the MTC time setting.
30. [PGM SEL] Key
* This is used to switch between programs 01 to 99.
This is also used to create new programs.
31. [SETUP] Key
* This is used to go into the setup mode to set various
parameters of the recorder and mixer.
INPUT SEL SOURCE
REC ASSIGN
BUSS DIRECT
REC TRK REC TRK
AUTO RTN
AUTO PUNCH
START IN OUT END IN ALIGN SEL OUT
DISP SEL PGM SEL SETUP
INT
MIXDOWN
A RTN
A PLAY
SCENE SEQ.
TIME BASE
CLIPBOARD
MARK
1 2 3 4 5 6 7
HOLD/ STORE EDIT
UNDO
/REDO
VARI
PITCH LOCATE SCRUB
P.EDIT EVT MEM
F FWD REWIND PLAY STOP RECORD
CLIPBOARD PLAY
LOCATE ABS 0
LOCATE REC END
PREV NEXT
JOG
SHUTTLE
AUTO
PUNCH
EXIT/NO
EJECT
ENTER/YES
FADER
ADJUST
LEVEL
ADJUST
SHIFT
CD PLAY
25 26 27 28 29 30 31
36
37
39
38
46
45
44
51
50
56
55
53
54
52
49
48
47
42
41
40
43
35
32
33
34