Maxtor pmn - Manual (Page 12)

5. Operation
9
3) Use numbers button [1], [2], [3], and [4]
button to enter password.
Password consists with numbers from
1 to 8 digits.
1) Press [MENU] button to enter the
2) LOGIN DVR SYSTEM window appears as
Factory default password set by manufaturer is as below.
ADMIN (Administrator) : 1 USER (User) : 2
NOTICE : We recommend you to set your own password as per procedure ID/PW SETUP in page 25.
5) After input password, press [MENU] button again to enter into SYSTEM SETUP menu.
NOTICE : When logged into USER MODE, only DISPLAY SETUP and TIME/DATE TYPE SETUP is possible.
system menu after starting the system.
If password entered matches previously set number, ADMIN GRADE LOGIN OK message appears.
If password entered does not match previously set number CURENT PW INPUT ERROR message
appears.
LOGIN DVR SYSTEM
PASSWORD ( )
1,2,3,4 : INPUT PASSWORD
MARK : ERASE PASSWORD
Enter the password
default P/W : 1
1
Input or modify
2
NOTICE : Be sure to memorize the changed password. In case you forgot own password, contact
dealer to get master password which will allow you to enter into SYSTEM SETUP again for new
password setting.
Login DVR SYSTEM
shown on the left.
4) Use [PIP] button to correct or delete you
entered.
The system is equipped with two passwords.
5. Operation
22
MOTION MASK SETUP 4
SELECT VER LINE : Select all cells in a vertical line.
CLEAR VER LINE : Clear all cells in a vertical line.
SELECT HOR LINE : Select all cells in a horizontal line.
CLEAR HOR LINE : Clear all cells in a horizontal line.
SELECT BLOCK : Select by BLOCK.
CLEAR BLOCK : Clear the BLOCK.
SELECT ALL CELLS : Set all cells.
CLEAR ALL CELLS : Clear all cells.
1. Press [P/T] button to choose desired EDIT mode.
You can select setting or clearing cell by cell, block by block, vertical line, horizontal line, or all cells.
2. Use [LEFT] or [RIGHT] button to select motion detection area, and press [ENTER] button to set.
Cells displayed in green color represents they are motion detection area, and the rest is no detection
area.
5. Press [MODE] button to select channel (1,2,3,4,quad) to select channel you want to set.
Whenever [MODE] button is pressed, it changes channel (camera tile on the bottom of display) is
changed in the sequence of 1, 2, 3, 4, Quad.
4. Detected area is indicated in green, and no detection area is indicated as colorless.
Setup is possible only in the full screen mode.
When [ENTER] button is pressed, “SELECT BLOCK
START” is displayed on the top.
Then select blocks using direction buttons.
and press [ENTER] button to set.
EDIT MODE : SELECT EACH CELL
P/T : CHANGE EDIT MODE
MODE : CHANGE CHANNEL
ENTER : MASK ON/OFF
: CURSOR MOVE
With the direction button,
choose MASK area.
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT ALARM SETUP
ALARM LIST SETUP
MOTION SETUP
MOTION MASK SETUP
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITION & PROCESSING
Log-in Log-in 1.
MOTION MASK SETUP
NOTICE : To protect hard drive from damaged, turn off the power switch of DVMR unit after you first
press [MENU] button. If you press [MENU] button, DVMR unit stops recording, and HDD
head is not in the process of writing.
If you entered into SYSTEM SETUP menu with User password, you are allowed to change limited
numbers of settings in SYSTEM SETUP menu, and you have to enter into SYSTEM SETUP menu
after input Administrator password to change all settings like setting related to recording.
Set motion detection area
independently for channel to which
camera is connected.