Metz 48 AF-1 - Manual (Page 70)

70
ķ
the lens focal length. In this case auto-zoom mode is not possible! After switching
on the flash unit, „Zoom“ appears in the display and the current zoom position
of the main reflector
ቫ appears.
Setting procedure
• Press button combination „Select“ until „Zoom“ appears flashing next to the
zoom position (mm).
• Apply the setting desired with the buttons ( + ) and ( - ). The flashing display
changes to „M.Zoom“ for manual zoom mode. The following zoom positions
are possible for the main reflector:
24 - 28 - 35 - 50 - 70 - 85 - 105 mm (35 mm format).
The setting takes effect immediately. After about 5 seconds the display stops
flashing and the setting is saved automatically.
When the camera transmits the lens focal length to the flash unit and a
manual zoom setting results in the shot not being completely lit by the
main reflector (for example, spot effect), the display of the zoom position
of the main reflector flashes as a warning!
Tip:
If you do not necessarily need the full guide number and maximum flash range
of the flash unit, you can leave the zoom reflector at the position for the shortest
focal length of the zoom lens. This will provide full light coverage of the picture
and eliminate the need to continually adjust it to the focal length of the lens.
Example:
You use a zoom lens with a focal length range of 35 mm to 105 mm. In this
case, you set the position of the main reflector of the flash unit to 35 mm.
Resetting to auto-zoom
• Touch the shutter release to begin a data transfer between the flash unit and
the camera.
• Press the button combination „Select“ until „M.Zoom“ appears flashing next to
the zoom position (mm).
☞
• Press the button ( + ) until the 105 mm position has been exceeded. The flas-
hing display „M.Zoom“ changes to „Zoom“ (= auto-zoom mode) and the
zoom position of the main reflector
ቫ is automatically adjusted to the lens
focal length. The setting takes effect immediately. After about 5 seconds the
display stops flashing and the setting is saved automatically.
The return from manual zoom mode to auto-zoom mode also occurs if the
flash unit is switched on again with the main switch
ቢ.
Wide-angle diffuser
With the wide angle diffuser
ቩ, focal lengths of 18 mm or more can be illumi-
nated (35 mm format).
Pull the wide-angle diffuser
ቩ out from the main reflector as far as it will go, and
then release it. The wide-angle diffuser ቩ automatically folds downwards. The
main reflector ቫ automatically moves to the required position. The distance rea-
dings and the zoom value are corrected to 18 mm on the display panel.
To insert the wide-angle diffuser
ቩ, turn it upwards 90° and push it all the way in.
Mecabounce 58-90
If the Mecabounce 58-90 (optional accessories, see 17) is fitted to the main
reflector
ቫ of the flash unit, the main reflector is automatically guided to the
position required. The distance data and zoom factor are corrected to 16 mm.
9.2 Remote slave flash mode ( )
The flash unit supports the wireless Sony Remote System in slave flash operation,
whereby one or more slave flash units can be remotely controlled in a wireless
manner via the camera’s integrated flash unit functioning as a controller flash
unit. In so doing, the flash of the controller flash unit only has a control function
for the slave flash unit and is not itself involved in the exposure of the given shot.
The slave flash units must be able to receive the light from the controller flash unit
via their integrated sensor for remote operation
ቤ .
Remote slave flash operation is only supported by digital reflex cameras!
For setting the remote slave flash operating mode there are two options.
☞
SL
☞
707 47 0151.A1 Inh. 48 AF-1Sony 26.11.2007 10:32 Uhr Seite 70