McIntosh C2200 - Manual (Page 15)

15
Setup
Input Trim Level
Various Source Components can have slightly different vol-
ume levels. This could result in the constant need to readjust
the C2200 Volume Control when switching between differ-
ent Input Sources. A Volume Trim Feature on the C2200
allows the adjustment of levels for each of the Source In-
puts, so that they have the same relative volume. The Tuner
and CD Inputs are used in the following example.
Notes: The possible range of adjustment in volume level is
± 6dB. The Tape/Record Output Levels are uneffected
by any changes in the Trim Settings. Any TRIM
adjustments made are retained in permanent memory
and can be changed only by performing a new TRIM
procedure. The Tuner Input Volume Level can serve as
a reference or choose another Input Source that is
frequently listened to as the reference. The reference
Input Source should be set to a Trim Level of 00.
1. Rotate the INPUT Control to select the Tuner Input and
adjust the VOLUME Control to the desired listening
level.
2. Press the SETUP Push-button to access the Setup
Mode.
3. The Front Panel Alphanumeric Display will change and
the Red LED above the SETUP Push-button will be il-
luminated.
4. Rotate the METER LIGHTS (Menu) Control until the
words TRIM 00 TUN appears. Refer to figure 5.
5. Rotate the INPUT Control until the words TRIM 00
CD appears. Refer to figure 6.
Figure 7
Figure 5
Figure 6
6. Rotate the VOLUME Control until the Volume Level of
the CD Input is the same as the Tuner Volume Level.
Refer to figure 7. Figure 7 indicates a 2.5dB decrease in
the CD Level.
7. Rotate the INPUT Control until the next desired Input
Source Name is displayed.
8. Repeat steps 5, 6 and 7 until all the Inputs with sources
connected to the C2200 have the same relative volume
levels when switching between them.
9. Press the SETUP Push-button to exit the Setup Mode.
Note: The Trim Level can also be set via the Remote
Control. A table has been provided on page 17 to
record the changes to the various inputs from the
default settings.
4. Press the SETUP Push-button to exit the Setup Mode.
To set the Front Panel Alphanumeric DISPLAY Brightness
when the Meter Illumination is Off, perform the following
steps.
5. Rotate the Front Panel METER LIGHTS (Menu) to
switch Off the Meter Illumination.
6. Press the SETUP Push-button to access the Setup
Mode.
7. Rotate the Front Panel METER LIGHTS (Menu) Con-
trol until the word DISPLAY 5 appears.
8. Rotate the BALANCE (Select) Control until the desired
Display Brightness is achieved. This sets the Brightness
Level with the Meters Illumination Off.
9. Press the SETUP Push-button to exit the Setup Mode.
Re-Title Inputs
The C2200 has eight Audio Inputs. These inputs already
have assigned titles that will allow for immediate hookup,
operation and enjoyment.
If these starting assignments do not match up with com-
ponents in your system, they may be reassigned from the
default settings. The following example will illustrate how
to rename the AUX Input to PHONO. When the Input Se-
lector is rotated to select what was originally the AUX In-
put, PHONO will now appear on the Front Panel Alphanu-
meric Display and Power is now supplied to the Vacuum
Tubes in Phono Circuitry.
Notes: 1. Unused Inputs may be switched Off so they will not
appear when rotating through the input source
choices using the Input Selector and also will not be
available when using the Remote Control or Keypad.
Refer to figure 8.
2. The New Input Titles that are available for all the
Inputs (except for the AUX Input) includes TAPE 2,
LV, TV, and VCR2. The AUX Input Titles include
TAPE 2, LV, TV and PHONO.
Figure 8