Integra DTR-7.4 - Manual (Page 27)

27
Connecting the Power
• Before you plug in the DTR-7.4, confirm that all con-
nections have been made properly.
• Turning on the power may cause a momentary power
surge, which might interfere with other electrical
equipment on the same circuit, such as computers. If
this happens, use a wall outlet on a different circuit.
Plug the supplied power cord into this AC INLET.
• Do not use a power cord other than the one supplied
with the DTR-7.4. The power cord supplied is
designed for use with the DTR-7.4 and should not be
used with any other device.
• Never have the power cord disconnected from the
DTR-7.4 while the other end is plugged into the wall
outlet. Doing so may cause an electric shock. Always
connect by plugging into the wall outlet last and dis-
connect by unplugging from the wall outlet first.
Before you can use the remote controller, you must
perform steps 1 above and place the DTR-7.4 in the
standby state.
Note:
Any components connected via will also be turned
on when the remote controller’s On button is pressed.
Memory backup
The DTR-7.4 uses a battery-less memory backup sys-
tem in order to retain radio presets and other settings
when it is unplugged or in the case of a power failure.
Although no batteries are required, the DTR-7.4 must
be plugged into an AC outlet in order to charge the
backup system.
Once it has been charged, the DTR-7.4 will retain the
settings for several weeks, although this depends on the
environment and time will be shorter in humid climates.
Connecting the Supplied Power Cord
--/---
@. - ' / ABC DEF
PQRS TUV WXYZ
GHI JKL MNO
TV CH
TV VOL
RC- 550M
+10 0
1 2 3
4 5 6
7 8 9
THX
DSP DSP
+
-
+
-
Direct Tuning
Caps Delete Language Loca t ion
Album Ar tist Genre Playlist
Custom
Display
Dimmer
T V
Input
Sleep
Muting
Angle Subtitle Audio
Memory Search A-B Repeat
T V On Standby
Audio AD J
Exit Gu ide
Random Step / Slow Rec
Last Memory
Clear
Input
To p M enu Men u
Set up Retu rn
Zone 2
Input Mode
Macro
CH VOL Disc
Test Tone CH SEL
Pure A
Surround
Direct
Stereo
Re-EQ
All CH ST
Level + Level -
L Night Audio SEL
Enter
Master Volume Standby/On
Upsampling Pure Audio
Audio Selector Tape Tuner Phono Net Audio CD Video 1
VCR 1
Video 3 Video 2
VCR 2
Video 4 Video 5 DVD Zone 2 ( ) GRN Rec ( ) RED
A-FO RM Listening Mode Memory
Video 5 Input
Stereo Direct / Pure Audio DSP Surround THX
Clear
Rec Out Zone 2 Of f
Setup Tuning
Preset
Enter
Return
Dimmer Display
S Video Audio Video L R
Phones
Standby
Memory FM Mode
DTR-7.4
Digital
On
Standby
Standby/On
Standby indicator
Scroll Wheel
To wall outlet
AC INLET
DO NOT con-
nect the
power cord at
this time.
Power cord
(supplied)
Turning on the Power
1 Plug the power cord into an AC
wall outlet.
The Standby indicator will light up.
2 Press the Standby/On button to
turn on the DTR-7.4.
The display will light up and the Standby
indicator will turn off.
If you press the Standby/On button
again, the DTR-7.4 returns to the standby
state.
Turning on the Power from the
Remote Controller
1 Press the scroll wheel.
“AMP” appears on the remote control-
ler’s display. This is the mode for con-
trolling the DTR-7.4.
2 Press the On button to turn on the
DTR-7.4.
To set the DTR-7.4 to Standby, press the
Standby button.
Standby
Standby/On
Standby
Turn off
On
F
acilities and Connections