JVC RX-884RBK - Manual (Page 56)

51
English
Using the On-Screen Menus
MAIN MENU
SOUND CONTROL menu
SEA menu
SEA ADJUST menu
MAIN MENU
SOURCE :VCR1
VISUAL :VCR1
MODE :OFF
SOUND CONTROL
TUNER CONTROL
SETTING
VOLUME : 20
:ENTER
**
**
**
**
**
**
SOUND CONTROL
SURROUND LEVEL
SEA
BAL.:CNTR
LOUDNESS : OFF
INPUT ATT : NORMAL
SUBWFR LEVEL: 0dB
NEXT PAGE
:ENTER
** **
** **
SEA
SEA MODE :ROCK
SEA ADJUST
:OPERATE
** **
100 10kHz 1k
SETTING 1
SUBWOOFER : NO
FRONT SPK : LARGE
CENTER SPK : SMALL
REAR SPK : LARGE
CNTR DELAY : 3msec
REAR DELAY : 5msec
NEXT PAGE
:ENTER
** **
SETTING 1 menu
SETTING 2 menu
Creating Your Own SEA Mode (Also see page 33)
1. Press any button of ON SCREEN CONTROL
% / fi / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL
% / fi to move
to “SOUND CONTROL,”
then press @ / #.
The SOUND CONTROL menu appears.
3. Press ON SCREEN CONTROL
% / fi to move
to “SEA,” then press
@ / #.
The SEA menu appears.
4. Press ON SCREEN CONTROL
% / fi to move
to “SEA ADJUST,” then
press
@ / #.
The SEA ADJUST menu appears.
5. Press ON SCREEN CONTROL
% / fi / @ / # to adjust the SEA mode as you
want.
@ / # : Select the frequency ranges.
% / fi : Adjust the frequency levels.
6. Press SET to store the setting into the SEA USERMODE.
• If you press EXIT, without pressing SET in this step, you can return to the SEA
menu. (The adjustment you have made is active but not stored.)
7. When you finish, press EXIT repeatedly until the menu disappears from the
TV.
Basic Settings
1. Press any button of ON SCREEN CONTROL
% / fi / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / fi to move to “SETTING,” then press
@ / #.
The SETTING 1 or SETTING 2 menu appears.
3. Press ON SCREEN CONTROL % / fi to the setting item you want to adjust.
• To go to the SETTING 2 menu, move to “NEXT PAGE,” then press
@ / #.
• To go back to the SETTING 1 menu, move to “PREVIOUS PAGE,” then
press @ / #.
On the SETTING 1 and 2 menus, you can do the following:
“SUBWOOFER”:
Set the subwoofer information (See page 19).
“FRONT SPK”: Set the front speaker information ( See page 20).
“CENTER SPK”: Set the center speaker information (See page 20).
“REAR SPK”: Set the rear speaker information (See page 20).
“CNTR DELAY”: Adjust the delay time of the center speaker output (See page 21).
“REAR DELAY”: Adjust the delay time of the rear speaker output (See page 21).
“CROSSOVER”: Set the crossover frequency (See page 21).
“LFE ATT.”: Set the low frequency effect attenuator level (See page 22).
“COMP.”: Set the dynamic range compression (See page 22).
“DIGITAL 1/2/3”: Set the digital input terminal (See page 20).
SEA ADJUST
SEA USERMODE
SET:MEMORY
100 10kHz 1k
SETTING 2
CROSSOVER :100Hz
LFE ATT. : 0dB
COMP. : OFF
DIGITAL 1 : DBS
DIGITAL 2 : CD
DIGITAL 3 : MD
PREVIOUS PAGE
:ENTER
** **
EN47_62.RX-884R[E]/1.PM5 98.4.10, 11:26 AM 51