Jura Capresso X7-S - Manual (Page 9)

9
10. Coffee
10.1 Drawing off coffee / espresso
Ⅲ : SELECT PRODUCT
Ⅲ Place 1 or 2 cups, as necessary, under the coffee spout (4) and press
the required selection switch. The pre-brew system (I.P.B.A.S © )
moisturises the coffee powder, briefly interrupts the discharge and
then starts the actual brewing procedure.
You can interrupt the draw-off prematurely by pressing any of
the coffee draw-off buttons. In order to obtain outstanding
froth, you can adapt the coffee spout (4) individually to match
the size of your cups.
10.2 Drawing off cappuccino
Ⅲ
: SELECT PRODUCT
Ⅲ Put milk/Tetra Pak into a jug and immerse the cappuccino tube into
the milk.
Ⅲ Place 1 cup under the coffee spout and press the draw-off key .
The machine firstly prepares the milk froth, then the coffee (Fig. 3).
You can interrupt the milk froth and the coffee prematurely by
pressing the draw-off key once more.
10 min. after the draw-off of Cappuccino, a rinsing is auto -
matically started. The rinsing is announced in advance by an
acoustic signal.
10.3 Drawing off pots of coffee
Ⅲ
: SELECT PRODUCT
Ⅲ Place 1 pot under the coffee spout (4) and press the draw-off key
(pot of coffee). Your pot of coffee is brewed in a number of cycles.
The number of cycles is shown in the display.
You can interrupt the draw-off prematurely at any time by
pressing the draw-off key again.
11. Drawing off hot water
Ⅲ : SELECT PRODUCT
Ⅲ Place a cup under the pivoting nozzle (18) and press the draw-off
key .
Ⅲ : PORTION HOT WATER
Ⅲ The draw-off of the programme portion of hot water stops auto-
matically.
You can interrupt the draw-off prematurely at any time by
pressing the draw-off key again.
When water is drawn off, there can be splattering at the
beginning. The pivoting nozzle becomes hot. Avoid direct
contact with the skin.
12. Drawing off steam
Ⅲ : SELECT PRODUCT
Ⅲ Place a cup with the liquid to be heated under the pivoting nozzle
(18) and press the draw-off key .
Ⅲ : STEAM ACTIVE
Ⅲ To end the draw-off of steam, press the key .
When steam is drawn off, there can be splattering at the
beginning. The pivoting nozzle becomes hot. Avoid direct
contact with the skin.
13. Drawing-off milk froth
Ⅲ : SELECT PRODUCT
Ⅲ Pour milk/Tetra Pak into a jug and immerse the Cappuccino tube
into the milk.
Ⅲ Place 1 cup under the coffee spout (4) and press the draw-off
key .
The programme amount is prepared and stops automatically.
You can interrupt the draw-off prematurely at any time by
pressing the draw-off key again.
10 min. after the draw-off of milk, a rinsing is automatically
started. The rinsing is announced in advance by an acoustic
signal.
14. Switching the machine off
Ⅲ Switch the machine off with the ON/OFF
operating switch. A
rinsing is automatically started when the machine is switched off.
15. Programming
The following phases can be programmed:
ᮣ Grinding amount
ᮣ Temperature
ᮣ Amount of water
ᮣ Amount of milk
ᮣ Portion of hot water
ᮣ Water hardness
ᮣ Clock
ᮣ Machine on
ᮣ Machine off
ᮣ Draw-offs
ᮣ Language
15.1 Programming grinding amount
Ⅲ Switch your machine on the with ON/OFF
operating switch.
Ⅲ Press the key PROG. until an acoustic signal is heard.
Ⅲ
: ADJUST COFFEE QUANTITY / SELECT PRODUCT
Ⅲ Press the required draw-off key.
Ⅲ
: (selected product)
– ..............II.............. +
Ⅲ By pressing the key or you can determine the amount to be
ground.
Ⅲ To store, press the key PROG.
Ⅲ
: (selected product)
Ğ: 100% ġ: 0%
You can determine the allocation of the grinder “left” or “right”.
Ⅲ By pressing the key or you can change the values.
Ⅲ To store, press the key PROG.
Ⅲ
: ADJUST COFFEE QUANTITY / SELECT PRODUCT
Ⅲ Press the required draw-off key, the key in order to reach the
next phase or the key EXIT to quit the programming.
+
- +
- +
E