JVC DR-DX5SU - Manual (Page 48)

Filename [DX5SUS_10Timer Recording.fm]
Masterpage:Left+
48
EN
TIMER RECORDING ON HDD/DVD DECK
Page 48Thursday, 1 September 2005 14:35
You can program this unit to timer record as many as 32 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to
timer record the program.
1
Load a recordable disc if recording to DVD.
2
Press PROG to access the program top screen.
3
Press selection keys to select ACALENDAR PR.B, then press
ENTER.
● When APROGRAM FULL DELETE UNWANTED TIMER
PROGRAMS B appears on the TV screen, you need to cancel
some of the reserved programs. (A pg. 49)
4
Press selection keys to select the desired date, then press
ENTER.
5
Press selection keys to select
ARECORD TOB, then press
ENTER. Press selection keys
to select the desired recording
deck, then press ENTER.
6
Press selection keys to select
ASTARTB, then press ENTER.
Press selection keys to set
the desired start time, then
press ENTER.
● Each press of F G increases/decreases the start time in 1-
minute intervals.
● To increase/decrease the start time in 30-minute intervals,
press and hold
F G.
7
Press F G to select ASTOPB, then press ENTER. Press F G to
set the desired stop time, then press ENTER.
● Each press of F G increases/decreases the stop time in 1-
minute intervals.
● To increase/decrease the stop time in 30-minute intervals,
press and hold
F G.
8
Press selection keys to select ASOURCEB, then press ENTER.
Press F G to select the desired source.
9
Press selection keys to select ACHB, then press ENTER. Press
F G to select the desired channel.
10
Press selection keys to select ACONFIRMB, then press
ENTER.
11
Set the other recording options as required.
● Refer to step 8 in AVCR Plus+ Timer ProgrammingB
(A pg. 46).
12
Press selection keys to
select
AOKB, then press
ENTER to access the
Program Confirmation
screen.
13
Press selection keys to
select
AEXITB, then press
ENTER to complete timer
programming.
● To program another timer, press selection keys to select
ACONTINUEB, then press ENTER.
● If APROGRAM OVERLAPPEDB appears on the TV screen,
delete or modify the programs.
NOTES:
● When two successive programs are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited program is received during timer recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Manual Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
FGDE
PROG
ENTER
CABLE/DBS
DVD TV
Selection Keys
HDD
DBS 100
[MISC. ] XP
100
CATV
11:00PM
10:30PM
2 PROGRAM > CALENDAR PR. (2/3)
CONFIRM
01/08/03 WED 10:30PM - 11:00PM
RECORD TO
STOP
START
SOURCE
ENTER
SELECT
PROG
EXIT
PRESS [PROG] TO EXIT
SELECT WITH @
THEN PRESS [ENTER]
CH
Cable box and DBS Receiver Users
To timer record a satellite broadcast using Manual Timer
Programming:
A Perform AManual Timer ProgrammingB on this page.
B Set the cable box or DBS receiver to the appropriate channel
before the selected program begins.
C Leave the cable box or DBS receiver’s power on.
Relief Recording
When a program that is set for the DVD deck cannot be recorded
properly, the program is recorded to the HDD deck instead in the
recording mode as set.
● If the remaining capacity of the hard disk is not sufficient, the
program is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
● If AJUSTB is selected for the recording mode, the current
recording mode for the DVD deck is applied.
1:00 28:00
DBS 100
2
ENTER
SELECT
PROG
EXIT
PROGRAM > CALENDAR PR. (3/3)
PRESS [PROG] TO EXIT
SELECT WITH @
THEN PRESS [ENTER]
OK
INPUT NAME
CATEGORY
WEEKLY/DAILY
REC MODE
GARDENING
EDUCATION
MON-FRI (FOR A WEEK)
FR360
01/08/03 WED 10:30PM - 11:00PM
GARDENING
[EDUCATION] FR360
DX5SUS_00.book Page 48 Thursday, September 1, 2005 2:35 PM