Preparations, C connecting to a tv with component jacks, Progressive scan video playback available – JVC XV-NA77SL User Manual

Page 8: About the scanning mode, Pal ntsc remote y/c rgb/comp

Advertising
background image

Preparations

6

XV-NA77SL/GNT0036-002B/English

P

re

pa

ra

ti

on

s

C Connecting to a TV with component jacks

You can enjoy picture of high-fidelity color reproduction by
connecting the COMPONENT VIDEO OUT jacks on the unit to
your TV.

NOTES

• Be sure to connect the red and white plugs of the audio cable to

the FRONT RIGHT/LEFT jacks on the rear of the unit, as shown
in the illustration.

• Connect “Y” to “Y,” “P

B

” to “P

B

” (C

B

), “P

R

” to “P

R

” (C

R

) correctly.

• Set [ANALOG OUT] in the [AUDIO] preference display to [2-CH

STEREO] (see page 39).

• If your TV has component video input jacks of BNC type, use an

adapter which converts a pin jack to a BNC jack (not supplied).

Activating the Progressive scanning mode when playing
back DVD VIDEO discs recorded with PAL system
1. Set the PAL - NTSC - REMOTE selector on the rear panel to

“REMOTE.”

2. Press and hold down PAL/NTSC on the remote control unit

until [PAL] appears in the display window. (The [NTSC]
indicator in the display window goes off.)

3. Press and hold down VFP - PROGRESSIVE SCAN for a few

seconds.
The scanning mode switches between the Progressive
scanning and Interlaced scanning modes.
When the scanning mode is set to the Progressive mode, the
PROGRESSIVE indicator on the front panel turns on.

Activating the Progressive scanning mode when playing
back DVD VIDEO discs recorded with NTSC system
Set the PAL - NTSC - REMOTE selector on the rear panel to
“NTSC,” and then press and hold down VFP - PROGRESSIVE
SCAN on the remote control unit for a few seconds.
The scanning mode switches between the Progressive scanning
and Interlaced scanning modes.
When the scanning mode is set to the Progressive mode, the
PROGRESSIVE indicator on the front panel turns on.
Alternatively, proceed as follows:
1. Set the PAL - NTSC - REMOTE selector on the rear panel to

“REMOTE.”

2. Press and hold down PAL/NTSC on the remote control unit

until [NTSC] appears in the display window. (The [NTSC]
indicator in the display window turns on.)

3. Press and hold down VFP - PROGRESSIVE SCAN for a few

seconds.
The scanning mode switches between the Progressive
scanning and Interlaced scanning modes.
When the scanning mode is set to the Progressive mode, the
PROGRESSIVE indicator on the front panel turns on.

Depending on the [PICTURE SOURCE] setting on the
[PICTURE] preference display and whether the current DVD
VIDEO disc is film-source or video-source, the color of the
indicator differs, as shown in the table below. (See page 38.)

* While stopped in the Progressive scanning mode, the

PROGRESSIVE indicator is lit in red regardless of the
[PICTURE SOURCE] selection.

Progressive scan video playback available

In the Progressive scanning mode, you can enjoy high quality
picture with less flickers when the COMPONENT VIDEO OUT
jacks are connected to a TV or monitor that supports the
progressive video input.

About the scanning mode

Depending on the material source format, DVD VIDEO discs
can be classified into two types; film source and video source
(note that some DVD VIDEO discs contain both film source
and video source).
When the unit plays back a film source material, uninterlaced
progressive output signals are created using the original
information. When a video source material is played back, the
unit interleaves lines between the interlaced lines on each to
create the interpolated picture and outputs as the progressive
signal.

RIGHT

LEFT

AUD

IO

VIDEO

S-VIDEO

IN

Y

P

B

P

R

COMPONEN

T IN

RIG

HT

REA

R

LEF

T

COA

XIA

L

OPT

ICA

L

PCM

/ST

REA

M

DIGIT

AL OUT

AUD

IO OUT

VID

EO

S-V

IDE

O

Y

P

B

P

R

VIDEO SIGNAL

SELECT

OR

AV COMPU LINK

PAL

Y/C

NTSC

REM

OTE

RGB

/CO

MP.

VIDEO OUT

COMPONENT

AV OUT

SUB

-

WO

OFE

R

CEN

TER

PAL

NTSC

REMOTE

Y/C

RGB/COMP.

VFP-PROGRESSIVE
SCAN
PAL/NTSC

The unit

Blue

Red

Green

White

Red

Red

White

Audio cable (supplied)

Component video cable
(not supplied)

Red

Blue

Green

TV

Set the RGB/COMP. - Y/C
selector to “RGB/COMP.”

Setting of
[PICTURE SOURCE]

Source type of DVD VIDEO

Film source

Video source

AUTO

Green

Red

FILM

Green

Green

VIDEO (NORMAL)/
(ACTIVE)

Red

Red

XV-XV-NA77SL[B].book Page 6 Thursday, July 31, 2003 8:04 PM

Advertising