JVC RX-DV31 - Manual (Page 51)

46
English
3
Press the number buttons (1 – 10, +10) to
enter a track/group you want to program.
Ex.: To select the track/group number 3, press 3.
To select the track/group number 14, press +10 then
4.
To select the track/group number 40, press +10,
+10, +10 then 10.
• For DVD AUDIO ONLY: Enter a group number and a
track number in order.
• When you enter a track/group number that does not
exist on the loaded disc, your entry is ignored.
• The total program time is shown at the top of the
program screen on the display.
For DVD AUDIO: For VCD/SVCD/CD:
4
Repeat step 3 to program the next steps.
• Each time you enter a track number in the step at the
bottom of the program screen, the next steps appear.
5
Press 3.
Playback starts in the programmed order.
Note:
• For DVD AUDIO only: If you select a bonus group in step 3, the
key number entry indication appears. In this case, enter the key
number to program a track in the bonus group (see page 44).
To erase a step
Press cursor 5 (or ∞) to move to the desired step, then
press 7.
• To program the next steps again, press cursor ∞ repeatedly
to move to the blank step, then repeat step 3.
To stop the program playback
Press 7.
• When DVD AUDIO, VCD, or SVCD is played back, the
program screen appears again.
• To edit your program, repeat steps 3 and 4.
To cancel the program playback mode
Clear the program you made as follows:
1 Press 7 to stop playback.
2 Press ON SCREEN to turn on the on-screen bar.
3 Press 7.
• You can also clear the program by ejecting the disc or
turning off the unit.
To turn off the on-screen bar
Press ON SCREEN.
Note:
• When all the programmed tracks have been played, the program
playback stops.
4
Press cursor
∞ (or 5) repeatedly to change
the setting, then press ENTER.
Your adjustment is stored and the current VFP parameter
list appears again.
5
Repeat steps 2 to 4 to adjust other
parameters.
To turn off the VFP setting screen
Press VFP.
To activate your setting
Press VFP, then press cursor 3 (or 2) repeatedly to select
“USER1” or “USER2.”
Note:
• The VFP setting screen disappears if no operations are done for
about 10 seconds.
Program Playback
You can play up to 99 tracks on DVD AUDIO/VCD/SVCD/CD
in the desired order.
• You cannot use Resume play for program playback.
• You may program the same tracks more than once.
Before using the remote control, press DVD so that the
remote control works for the DVD player.
& While stopped
1
Press ON SCREEN repeatedly until the on-
screen bar with pull-down menu appears on
the TV.
2
Press cursor
3 (or 2) repeatedly to move
to PROG. in the pull-down menu, then press
ENTER.
For DVD AUDIO: For VCD/SVCD/CD:
The program screen appears on the TV and the
PROGRAM indicator lights up on the display.
• 10 steps appear at a time on the program screen.
PROGRAM
No. Group Track
1
2
3
4
5
6
7
8
9
10
Total Program Time 00:00:00 PROGRAM
No.
1
2
3
4
5
6
7
8
9
10
Total Program Time 00:00:00
PROGRAM
No.
1
2
3
4
5
6
7
8
9
10
2 – 3
Total Program Time 00:04:14
Group Track
PROGRAM
No.
1
2
3
4
5
6
7
8
9
10
3
Total Program Time 00:04:14
39-48_RX-DV31SL[UW]f.p65 03.4.22, 18:58 46