JVC DR-MH20SUJ - Manual (Page 48)

Filename [DR-MH30UJ_07Timer Recording.fm]
Masterpage:Left+
48
EN
TIMER RECORDING
Page 48 Monday, 12 July 2004 14:25
You can program this unit to timer-record as many as 32 programs.
If you do not know the VCR Plus+ number for the program you
wish to record, use the following procedure to set your unit to
timer-record the program.
1
Load a recordable disc if recording to DVD.
2
Press PROGRAM to access the program top screen.
3
Press rtw e to select “CALENDAR PR.”, then press ENTER.
● When “PROGRAM FULL DELETE UNWANTED TIMER
PROGRAMS” appears on the TV screen, you need to cancel some of
the reserved programs. (
੬ pg. 49)
4
Press rtw e to select the desired date, then press ENTER.
5
Press rt to select “RECORD
TO”, then press ENTER. Press
rt to select the desired
recording deck, then press
ENTER.
6
Press rt to select “START”, then press ENTER. Press rt to
set the desired start time, then press ENTER.
● Each press of rt advances/goes back the start time in 1-min.
increments.
● To advance/go back the start time in 30-min. increments, press and
hold rt.
7
Press rt to select “STOP”, then press ENTER. Press rt to
set the desired stop time, then press ENTER.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press and
hold rt.
8
Press rt to select “SOURCE”, then press ENTER. Press rt
to select the desired source, then press ENTER.
9
Press rt to select “CH”, then press ENTER. Press rt to
select the desired channel.
10
Press rt to select “CONFIRM”, then press ENTER.
11
Set the other recording options as required.
● Refer to step 8 in “VCR Plus+ ® Timer Programing” ( ੬ pg. 46).
12
Press rt to select “OK”,
then press ENTER to access the
Program Confirmation screen.
13
Press w e to select “EXIT”,
then press ENTER to complete
timer programing.
● To program another timer, press
w e to select “CONTINUE”,
then press ENTER.
● If “PROGRAM OVERLAPPED” appears on the TV screen, see
page 49.
NOTES:
● When two successive programs are recorded on a DVD-RW disc with
Manual Timer Programing function, the beginning of the second one
may be left off the recording.
● If the copy limited program is received during timer-recording, the unit
enters Record Pause mode. Recording starts again if it is switched to
a recordable broadcast during the time you programed.
Manual Timer Programing
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
rtwe
AUX
PROGRAM
ENTER
CABLE/DBS
DVD TV
01/08/03 WED 10:30PM - 11:00PM DBS 100
[MISC. ] XP
PRESS [PROGRAM]
TO EXIT
SELECT WITH [ ]
THEN PRESS [ENTER]
100 CH
DBS SOURCE
11:00PM STOP
10:30PM START
HDD RECORD TO
PROGRAM > CALENDAR PROG. (2/3)
O K
ENTER
SELECT EXIT
PROGRAM
2
Cable Box and DBS Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programing:
A Perform “Cable Box and/or DBS Receiver Control Setting”
(
੬ pg. 24).
B Perform “Manual Timer Programing” (੬ pg. 48).
C Leave the cable box or DBS receiver’s power on.
Relief Recording
When a program that is set for the DVD deck cannot be recorded
properly, the program is recorded to the HDD deck instead in the
same recording mode as set.
● If the remaining capacity of the hard disc is not sufficient, the
program is recorded to the DVD deck until the remaining capacity
of the DVD disc lasts.
● If “JUST” is selected for the recording mode, the current recording
mode for the DVD deck is applied.
01/08/03 WED 10:30PM - 11:00PM DBS 100
[EDUCATION] GARDENING FR360
1:00 28:00
ENTER
SELECT EXIT
PROGRAM
PRESS [PROGRAM]
TO EXIT
SELECT WITH [ ]
THEN PRESS [ENTER]
FR360 REC MODE
MON-FRI (FOR A WEEK) WEEKLY/DAILY
EDUCATION CATEGORY
GARDENING INPUT TITLE
PROGRAM > CALENDAR PROG. (3/3)
O K
2
DR-MH30UJ_00.book Page 48 Monday, July 12, 2004 3:17 PM