Using the cassette deck, Using the cassette deck (recording), Standard recording – JVC SP-UXV100 User Manual

Page 18: Things to know before you start recording, 3 check the recording direction for the tape, 5 press the rec button on the unit

Advertising
background image

14

Using the Cassette Deck
(Recording)

When the System is in use, the display shows other items as well.
For simplicity, only the items described in this section are shown here.

TAPE

@

#

7

REMOTE CONTROL RM-SUXV10E

CANCEL

TREBLE

FM/AM

FM

MODE

DISPLAY

SLEEP

AUX

TAPE

CD

CD

BASS

AHB
PRO

DOWN

RANDOM

UP

AUTO

PRESET

REPEAT

SET

PROGRAM

VOLUME

CAUTION:
If a recording you make has excessive noise or
static, the Unit may have been too close to a TV
which was on during the recording. Either turn
off the TV or increase the distance between the
TV and the System.

Adhesive tape

Type II detection
slot

Recording onto a tape from any of the sound sources is simple. Just
place a tape in the Cassette Deck, have the source ready, make one
or two settings, and you’re ready to record. For each source the
procedure is a little bit different so we explain each separately. But
first, here are a few things to make your recordings better.

Things to know before you start

recording –––––––––––––––––––––––––––––

It should be noted that it may be unlawful to re-
record pre-recorded tapes, records, or discs without
the consent of the owner of copyright in the sound or
video recording, broadcast or cable program and in
any literary, dramatic, musical, or artistic embodied
therein.

■ When you want to record onto both sides of a tape, you can set

Reverse mode to do so. Recording automatically stops after
recording in the

2 direction. Therefore, make sure that the tape

direction is

3 when recording with Reverse mode on.

■ The recording level, which is the volume at which the new tape

is being made, is automatically set correctly, so it is not
affected by the VOLUME control on the System. Nor is it
affected by adjusting the sound effects. Thus, during recording
you can adjust the sound you are actually listening to without
affecting the recording level.

■ Two small tabs on the back of the cassette tape, one for side A

and one for side B, can be removed to prevent accidental
erasure or recording.

■ To record on a cassette with the tabs removed, you must cover

the holes with adhesive tape first. However, when a type II tape
is used, only cover part of the hole as shown, since the other
part of the hole (Type II detection slot) is used to detect the
tape type.

■ Type I and Type II tapes can be used for recording.

Note:

At the start and end of cassette tapes, there is leader tape
which cannot be recorded onto. Thus, when recording CDs
or radio broadcasts, wind on the leader tape first to ensure
that the recording will be made without any music part lost.

Standard Recording

You can record any sound source to tape as follows:

1 Insert a blank or erasable tape into the

Cassette Deck.

2 If you want to record on both sides of a

tape, press the REV. MODE button on the
Unit until the

indicator is lit.

When using Reverse mode, insert the tape so that it will be
recorded in the forward

3 direction.

3 Check the recording direction for the

tape.

Make sure that the Tape Direction indicator is the same as that
for the tape in the Cassette Deck. If the directions are different,
press the TAPE

@ # button to correct the tape direction and

then press the

7 button to stop the tape.

4 Prepare the source by, for example,

tuning in a radio station or turning on
connected auxiliary equipment.

Note:

For CD recording, refer to “CD Direct Recording” on page
15.

5 Press the REC button on the Unit.

The REC indicator lights up and the System begins recording.

Notes for using Reverse mode for recording

When recording in Reverse mode, the System automatically stops
when it reaches the end of the reverse

2 direction. To record on

both sides of a tape, make sure that the recording direction for the
tape inserted is forwards

3, and that the Tape Direction indicator is

also forwards

3, before you start recording.

To stop at any time during the recording
process

Press the

7 button.

CD

#¥8

REC

Tape Direction indicator

Reverse Mode indicator

REC indicator

DOWN

UP

MULTI CONTROL

TAPE

FM/AM

CD

STANDBY

PHONES

AUX

REC

REV

MODE

AHB
PRO

TIMER

CLOCK

VOLUME

CD

OPEN/CLOSE

REC

REV. MODE

7

CD

#¥8

TAPE

@

#

EN10-22.UX-V100[B]f

12/12/00, 12:33 PM

14

Advertising
This manual is related to the following products: