JVC RX-668RBK - Manual (Page 36)

33
English
Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC
components are preset in the remote control.
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK-3 (SYNCHRO) jacks (see page 27) in addition to the
connections using cables with RCA pin plugs (see page 5).
• Aim the remote control directly at the remote sensor on the
receiver.
• If you use the buttons on the front panel or the menu function to
choose a source, the remote control will not operate that source.
To operate a source with the remote control, the source must be
selected using buttons on the remote control.
• Refer also to the manuals supplied with your components.
Sound control section (Amplifier)
After pressing SOUND CONTROL, you can perform the following
operations:
SURROUND : Selects the DSP modes.
CENTER – / + : Adjusts the center speaker output level for the
Surround/DVD MULTI playback modes.
REAR•L – / + : Adjusts the left/right rear speaker output level for
the DSP modes.
Adjusts the left rear speaker output level for the
DVD MULTI playback mode.
REAR•R – / + : Adjusts the right rear speaker output level for the
DVD MULTI playback mode.
DELAY : Selects the delay time of the rear speaker sound.
(Only works when “PRO LOGIC” is selected.)
EFFECT : Selects the effect level for the DSP modes.
TEST : Turns on or off the test tone output for the
Surround mode.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using 10 keys;
otherwise, 10 keys cannot be used for operating your target source.
CD player
After pressing CD, you can perform the following operations on the
CD player:
3: Starts playing.
4 4 4 4 4: Returns to the beginning of the current (or
previous) track.
¢ ¢ ¢ ¢ ¢: Skips to the beginning of the next track.
7: Stops playing.
8: Pauses playing. To release it, press 3.
1 – 10, +10 : Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
CD player-changer
After pressing CD-DISC, you can perform the following operations
on a CD player-changer:
3:
Starts playing.
4 4 4 4 4:
Returns to the beginning of the current (or previous)
track.
¢ ¢ ¢ ¢ ¢:
Skips to the beginning of the next track.
7:
Stops playing.
8:
Pauses playing. To release it, press
3.
1 – 6, 7/P : Select the number of a disc installed in a CD player-
changer.
After pressing CD, you can perform the following operations on the
CD player-changer:
1 – 10, +10 : Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
ON SCREEN
SLEEP ONE TOUCH
OPERATION
TV/VIDEO
3 2 1
6 5 4
9 8 7/P
+10 0
TV
SOUN D
RE C P AUS E
TEXT DISPLAY
RM-SR668RU
REMOTE CONTROL
MUTING DVD M
ULT
I
/I
+ PTY
PTY SEARCH
PTY –
PH ONO
FM/A M
DVD
CD
VCR
VOLUME VCR CH TV VOL. TV CH
10
SET EXIT CD-DISC
SOUND
CONTROL TV VCR AUDIO
SURROUND TEST DELAY
EFFECT – CENTER +
– REAR•L +
ENTER
RETURN
MENU
– REAR•R + 100+
8
DISP
LAY
TAPE/M
D
Tuner
After pressing FM/AM, you can perform the following operations:
FM/AM : Alternates between FM and AM (MW/LW).
1 – 10, +10 : Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
PTY SEARCH : Searches for a program by PTY codes.
PTY – / + : Selects the PTY codes.
DISPLAY : Shows the RDS signals.
EN23_36.RX-668R[E]/2 99.1.28, 1:12 PM 33