JVC DR-MV5BEK - Manual (Page 32)

Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Left+
32
EN
TIMER RECORDING
Page 32Wednesday, 31 August 2005 19:58
On-Disc Timer Programming is a function used with discs that are
especially intended for a specific programme. The disc is then
programmed for a programme you always watch every day or
every week. Since older programmes are automatically
overwritten, a single DVD-RAM/RW (VR mode) disc can be used
without worrying about how much recording capacity remains.
(
੬ pg. 33)
You can programme each disc to timer-record as many as
8 programmes.
To Make The Disc For On-Disc Timer Programming
1
Load a recordable disc.
2
Press DVD so that the DVD lamp lights up on the unit.
3
Press PROG to access the Programme Check screen.
4
When On-Disc Timer Programming is made for the first
time on the disc
Press rt to select “DISC TIMER PRGM”, then press ENTER.
● When some programmes are recorded on the disc, a caution
message appears. In such a case, backup the programmes as
required, then format the disc before making On-Disc Timer
Programming. (
੬ pg. 89)
When On-Disc Timer Programming has already been made on
the disc
Press rt to select “DISC TIMER PROGRAMME”, then press
ENTER.
5
Press rt to set the desired date.
● The current date appears on the TV screen. The date you enter
appears in its place.
6
Press w e to select “START”, then press rt to set the desired
start time.
● Each press of rt advances/goes back the start time in 1-min.
increments.
● To advance/go back the start time in 30-min. increments, press and
hold rt.
7
Press w e to select “STOP”, then press rt to set the desired
stop time.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press and
hold rt.
8
Press w e to select “TV PROG”, then press rt to select the
desired channel.
9
Set “DAILY/WEEKLY” option.
● Refer to step 6 in “VIDEO Plus+ Timer Programming” ( ੬ pg. 29).
● It is necessary to set “DAILY/WEEKLY” option for On-Disc Timer
Programming. (
੬ pg. 30, “Weekly/Daily Recording”)
10
Set the other recording options as required.
● You can select XP, SP, LP, EP or FR480 mode for “REC MODE”.
However, you cannot select FR (JUST), FR60–FR360 and FR420.
● Refer to step 6 in “VIDEO Plus+ Timer Programming” ( ੬ pg. 29).
● It is not possible to use the Free Rate function. ( ੬ pg. 62)
11
Press ENTER to access the Programme Confirmation screen.
12
Press ENTER to complete timer programming.
● To programme another timer, repeat steps 3 – 12.
To Timer-record The Programme With The Programmed Disc
1
Load a programmed disc.
2
Press TIMER #. The unit turns off and “ ” appears on
the front display panel. The DVD timer indicator also lights up on
the unit and the unit is automatically turned off.
● To disengage the timer mode, press TIMER # again.
NOTES:
● On-Disc Timer Programming is not possible on a DVD-RW disc
formatted in video mode. (
੬ pg. 89)
● The information of a programme recorded with On-Disc Timer
Programming is not stored in the library. ( ੬ pg. 71)
● The play list is not created for the programmes recorded with On-Disc
Timer Programming. (
੬ pg. 68)
● Basic Recording ( ੬ pg. 26), VIDEO Plus+ Timer Programming
(
੬ pg. 29), Manual Timer Programming (੬ pg. 31) are not possible
on the On-Disc Timer programmed disc.
● The beginning of a programme may not be recorded. Also, if the 1st
programme’s recording stop time and the 2nd programme’s recording
start time is the same, the ending of the 1st programme may not be
recorded.
● If there is a power cut while recording, the recordings before the
power cut are not guaranteed.
On-Disc Timer Programming (DVD Deck
Only)
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
ATTENTION:
● On-Disc Timer Programming is possible only with the disc for On-
Disc Timer Programming.
● If data is recorded on a disc for On-Disc Timer Programming using
a unit from another manufacturer, On-Disc Timer Programming
may no longer function properly.
rtwe
ENTER
PROG
TIMER
DVD
Satellite Receiver Users
To timer-record a satellite broadcast using the On-Disc Timer
Programming function:
A Perform “On-Disc Timer Programming (DVD Deck Only)”.
B Set the satellite receiver to the appropriate channel before
the selected programme begins.
C Select “L-2” in step 8.
D Leave the satellite receiver’s power on.
MV5SEK_00.book Page 32 Wednesday, August 31, 2005 7:58 PM