JVC CA-HXZ30 - Manual (Page 17)

12
English
Listening to FM and AM Broadcasts
Setting the AM Tuner Interval Spacing
Some countries space AM stations 10 kHz apart, and some
countries use 9 kHz spacing.
• You can only change the AM tuner interval spacing while
tuning in to an AM station. (10 kHz is the initial setting.)
On the unit ONLY:
Press while holding down
7.
• Each time you press these buttons, the
AM tuner interval spacing alternates
between 9 kHz and 10 kHz.
Tuning in to a Station
1
Press FM/AM.
The unit automatically turns on and
tunes in to the previously received
station (either FM or AM).
• Each time you press the button, the band alternates
between FM and AM.
2
Start searching for stations.
On the unit:
Press and hold TUNING +
or TUNING – for more than 1
second.
On the remote control:
Press and hold
¢ (¡)
or
4 (1) for more
than 1 second.
The unit starts searching for
stations and stops when a station of sufficient signal
strength is tuned in.
• If a program is broadcast in stereo, the ST (stereo)
indicator lights up.
To stop searching, press TUNING + or TUNING – (or
¢ (¡) / 4 (1) on the remote control).
When you press TUNING + or TUNING – (or ¢ (¡) /
4 (1) on the remote control) briefly and repeatedly
The frequency changes step by step.
To change the FM reception mode
On the remote control ONLY:
When an FM stereo broadcast is hard to
receive or noisy, press FM MODE so that the
MONO indicator lights up on the display.
Reception will improve.
To restore the stereo effect, press FM MODE again so that
the MONO indicator goes off. In this stereo mode, you can
hear stereo sounds when a program is broadcasted.
Presetting Stations
You can preset 30 FM and 15 AM stations.
In some cases, test frequencies have been already memorized
for the tuner since the factory examined the tuner preset
function before shipment. This is not a malfunction. You can
preset the stations you want into memory by following the
presetting method.
• There is a time limit in doing the following steps. If the setting
is canceled before you finish, start from step 2 again.
On the unit ONLY:
1
Tune in to the station you want to preset.
• See “Tuning in to a Station.”
2
Press SET/DISPLAY.
3
Turn PRESET + / – to select a
preset number.
4
Press SET/DISPLAY again.
The tuned station in step 1 is stored in the preset number
selected in step 3.
• Storing a new station on a number already used erases
the previously stored one.
When you unplug the AC power cord or if a power
failure occurs
The preset stations will be erased in a few days. If this happens,
preset the stations again.
Tuning in to a Preset Station
1
Press FM/AM.
The unit automatically turns on and tunes in to the
previously received station (either FM or AM).
• Each time you press the button, the band alternates
between FM and AM.
2
Select a preset number.
On the unit:
Turn PRESET + / –.
On the remote control:
Press the number buttons.
Ex.: For preset number 5, press 5.
For preset number 15, press
+10, then 5.
For preset number 25, press
+10, +10, then 5.
For preset number 30, press
+10, +10, then 10.
FM / AM
T U N IN
G /BEEP
AUX
FM/AM FM MODE
SET
/DISPLAY
PRESET
T U N IN
G
PRESET
T U N
IN
G
FM / AM
FM MODE
T U N IN
G /BEEP
STANDBY
EN09-12.HX-Z10&30[UW&UJ]1 03.3.19, 10:55 AM 12