Scag Power Equipment WILDCAT STWC48V-25CV - Manual (Page 49)

45
R
Section 8
61v CUTTER DECK
Ref.
No.
Part No. Description
Ref.
No.
Part No. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
461862
43687
424371
481625-01
481632
04003-26
422478
04017-27
04043-06
04021-05
461846
04001-11
04001-12
04021-10
04020-09
45944
04001-41
48038
04001-154
04063-08
483246
04043-04
04001-176
04019-03
04001-172
48100-15
04030-03
04040-15
483703
04021-09
461940
461946
483286
04110-03
461663
43589
481024
481022
48114-04
48677
43644
43312
43296
481025
43297
481035
43590
482879
483287
424367
483210 Cutter Deck Velocity Plus
Boss, Spring Anchor
Bracket, LH Spring Anchor 61V
Wing Nut, 3/8-16
Anti-Scalp Wheel
Bolt, Carriage 3/8-16 x 4”
Bracket, Anti-Scalp Wheel
Bolt, Serr. Flng. 3/8-16 x 1”
Flatwasher, 5/8” Hardened
Locknut, 3/8-16 Center Lock
Discharge Chute
Bolt, Hex Hd. 5/16-18 x 1-1/2”, Rear
Bolt, Hex Hd. 5/16-18 x 1-3/4”, Front
Nut, Elastic Stop 5/16-18
Nut, 5/8-11 UNC
Shaft, Roller
Bolt, Hex Hd. 5/8-11 x 9-1/2”
Roller, Rear
Bolt, Hex Hd. 5/16-18 x 4-3/4”
Key, 1/4 x 1/4 x 2”
Spring, LH Deck Drive
Flatwasher, 3/8” (.938 x .391 x .105")
Bolt, Hex Hd. 5/16-18 x 1-3/4” Grd. 8
Nut, Serr. Flng. 5/16-18
Bolt, Hex Hd. 1/4-20 x 1” Grd. 8
Bushing, .376 ID Oilite®
Lockwasher 5/16”
Flatwasher 5/16”
Spring, RH Deck Drive
Nut, Elastic Stop 3/8-16
Idler Arm Assembly, LH Drive
Idler Arm Assembly, RH Drive
Pulley, Tapered Bore 6.33” Dia.
U-Nut, 3/8-16
Spindle Assembly
Shaft, Spindle
Seal Upper
Bearing Assembly
Grease Fitting
Valve, Grease Relief
Housing, Spindle
Spacer, Outside
Spacer, Inside
Seal, Lower
Bushing, Bottom
Nut, Special 1-1/16 - 18
Spacer, Spindle
Cutter Blade 21”
Pulley, Double Groove 6.33” Dia.
Dust Shield
Idler Pulley, 5” Dia. 51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94 48181
424575
48926
483415
43689
48224
424209
451240
461516
04020-16
04021-13
48763
04001-79
48114-04
483243
04001-09
483378
424841
04003-23
04041-07
04001-77
483157
482295
45944
483167
04003-40
461929
04001-136
04001-19
04019-04
04030-04
43689
04003-12
483176
04040-04
04021-04
04001-19
04001-31
04021-11
04040-11
04001-46
04001-54
04021-09
483287 Idler Pulley, 5” Dia.
Belt Cover (61V)
Hub, Tapered 1-1/8” Bore
Idler Pulley, 3-1/2” Dia.
Pivot, Idler
Bearing
Turbo Baffle, Bolt On
Push Arm Shaft
Push Arm (Incl. 64, 60, 62)
Nut, 5/8-18 UNF
Nut, Elastic Stop 5/8-11
Rod End, 5/8 Male RH Thread
Bolt, Hex Hd. 5/8-11 x 4-1/2”
Grease Fitting, 90 Degree
Belt, Deck Drive 61V
Bolt, Hex Hd. 5/16-18 x 1”
Spring, Discharge Chute
Baffle Weldment, 61V
Bolt, Carriage 3/8-16 x 1”
Flatwasher, 3/8 (.391 x .938 x .105")
Bolt, Hex Hd. 3/8-16 X 3-1/2”
Belt, Deck Drive RH
Wheel, Anti Scalp
Roller Shaft
Bolt, Special
Bolt, Carriage 7/16-14 x 1-1/4”
Lever Assy., Deck Level
Bolt, Hex Hd. 3/8-16 x 1-1/2” Grd. 8
Bolt, Hex Hd. 3/8-16 x 1”
Nut, Serr. Flng. 3/8-16
Lockwasher, 5/16”
Pivot, Idler Short
Bolt, Carr. 5/16-18 x 3/4”
Wear Pad
Flatwasher, 5/16 (.344 x .688 x .065")
Nut, Center Lock 5/16”
Bolt, Hex Hd. 3/8-16 x 1”
Bolt, Hex Hd. 3/8-16 x 2-1/2”
Nut, Elastic Stop 7/16-14
Flatwasher, 7/16 (.500 x 1.250 x .083")
Bolt, Hex Hd. 3/8-16 x 2-1/4”
Bolt, Hex Hd. 3/8-16 x 3”
Nut, Elastic Stop 3/8-16
Pulley, Double Groove 6.33" Dia.