Sierra Products EF-4001B - Manual (Page 4)

4
Figure 7 Connection Panel Lower Right Side
Autolite Wiring Diagram
Figure 9 Do or h andle a sse m bly
Note - For best insert operation the flexible vent
installation sho uld no t have any tight be nds. T ry to
achieve a smooth sweep to the vertical rise.
SURROUND INSTALLATION
The surro un d sup plied w ith th e inse rt is adjus tab le in
height so as to allow for many installation perimeters.
1. After the insert is in position, install left and right surround
sides by attaching them to the two side brackets using the
four 1/4-2 0 bo lts provided. The retainer nuts on the
surround sid es m ay be installed at any vertical position to
accomm odate the installation.
2. Slide the surround top panel between the hopper top and
cover. Push the panel down until the screw holes align
with the side legs. Install the (4) #8 screws provided.
Install power cord into the receptacle on the right side of
the insert. Route cord behind surround leg and out to a
ground plus.
AUTOLITE INSTALLATION INSTRUCTIONS
Th e A uto Lite Sys tem is fa cto ry ins talle d w ith th e only
installation requ irem ents being the optiona l therm osta t.
Wall Thermostat Installation:
Th e wa ll therm osta t is des igned to autom atically reg ulate
the ro om tem pera ture fr om the c ontro l pane l heat s etting to
the “Off” setting based upon room tem perature. Rem ember
to leave the control panel on the "Medium or High" position
when utilizing the wall thermostat feature.
The following is a step by step procedure for installing the
optional wall therm ostat. Note conne ction terminals on left
side of unit at rear (Figure 7). Use 18/2 thermostat wire for
the installation.
a. Unplug he ater from wall outlet and 12V DC power!
b. Rem ove factory jump wire and hook up thermostat
wires to terminals (Figure 7).
c. Locate thermostat approximately 10 to 12 feet from
heater or in area that requires steady temperature.
d. Run thermostat wires from heater to thermostat along
wall or u nde r carpet e tc. an d ho ok wires to
thermostat terminals. On new construction you can,
of course, run wire in the walls before sheet rock or
paneling is done.
e. Reco nnect AC power.
f. Make sure all wiring is completed before plugging the
EA SYF IRE He ater b ack into the wall ou tlet.
IMPORTANT - Any electrical work performed on the
EA SYFIRE H ea ter shou ld be don e by qualifie d perso nn el.
Remote Control Thermostat Installation:
Th e re m ote the rm ostat is desig ne d to autom atic ally
regulate the room temperature from the control panel heat
setting to the “Off” setting base d upon roo m temp erature
and place m ent o f the re m ote therm osta t. Rem em ber to
leave the control panel on the "Medium or High" position
when utilizing the wall thermostat feature.
The following is a step by step procedure for installing the
optional remote thermostat. Note connection terminals on
rear of un it (Figure 7).
a. Unplug he ater from wall outlet and 12V DC power!
b. Mount millivolt style remote receiver box to rear of
stove using double-sided tape.
b. Rem ove factory jump wire and hook up thermostat
wires to terminals (Figure 7).
d. Re con nec t AC pow er an d follow instructions with
remote thermostat regarding set up.
IMPORTANT - Any electrical work performed on the
EA SY FIRE H ea ter shou ld be don e by qualifie d perso nn el.
DOOR HANDLE ASSEMBLY
The door handle and latch must be assembled and
adjusted prior to the operation of the stove.
1. Position hand le ass em bly throu gh d oor a nd s ecu re with
collar by sliding over shaft and tightening with allen
wrench provided.
2. Position latch on end of shaft with flat facing allen screw.
Depending on gasket, shaft will protrude approx. 1/4"
through back of latch collar. Snug allen screw.
3. To adju st do or, close a nd turn ha ndle so latc h co ntac ts
striker. Door gasket must contact firmly against front face
of unit. This can be che cked by closing against a piece of
pa pe r. Firm ly tug on pape r, if it m oves with solid
resistance the door is properly adjusted.