Smarthome 7307 - Manual (Page 12)

– 23 –
ADVANCED PROGRAMMING
1. Enter the current MPIN.
2. Press [ A ].
3. Press [ A ].
You will hear a long beep. The arm light, the red and green lights in zones
1 and the red lights in zones 3 and 4 go on. Zone 1 has the entry delay to
allow someone to enter through the front door and deactivate the system
before the siren sounds. This option does not have the exit delay so you
are not able to leave the premises without activating the alarm. Zone 2 (the
motion sensor), is off allowing movement in the premises and zones 3 & 4
are instant.
Option 2: Advanced Home 2 - use to secure the premises while staying in
the building. Delays the alarm to allow someone to enter the building and/or
walk in the monitored area of the motion sensor to deactivate the alarm.
1. Enter the current MPIN.
2. Press [ A ].
3. Press [ C ].
You will hear a long beep. The arm light, the red and green lights in zones
1 and 2 as well as the red lights in zones 3 and 4 go on. Zone 1 & 2 has the
entry delay to allow someone to enter through the front door and walk in the
area monitored by the motion sensor and deactivate the system before the
siren sounds. This option does not have the exit delay so you are not able
to leave the premises without activating the system. Zones 3 & 4 are instant.
Option 3: Chime Sequence - this sequence is used for testing the system
but it can also be used to subtly alert you when a zone has been activated.
Example, if a young child opens the front door, the Control Panel will emit a
two tone chime advising you that the front door has been opened. (See page 11
for programming information for the CHIME SEQUENCE.)
The three arm sequences above ; Advanced Home 1, Advanced Home 2 and
Chime Sequence along with the three sequences described in the STANDARD
PROGRAMMING; Away Sequence, Home Sequence and Night Sequence,
make up the six preprogrammed arm sequences.
However, if any of these six sequences do not satisfy your needs, you may
want to change the modes in certain zones. For example, your zone 2, (motion
sensor) is currently in delay mode. If your motion sensor is located in the base-
ment and you would like to change it to the instant mode, see below.
– 22 –
ADVANCED PROGRAMMING
STANDARD ARMING SEQUENCES
Each zone can be programmed to react 5 different ways when it receives a
signal from a remote sensor.
1. Chime Mode - represented by the green lights
When only the green light is on and the Control Panel receives a
signal from a remote sensor, the Control Panel emits a subtly two
tone chime.
2. Instant Mode - represented by the red lights
When only the red light is on and the Control Panel receives a signal
from the remote sensor, the Control Panel will activate the siren
instantly.
3. Delay Entry Mode - represented by the green and red lights
When both the green and red lights are on and the Control Panel re-
ceives a signal from a remote sensor, the lights will flash and the
Control Panel will beep for 30 seconds before the alarm sounds.
These 30 seconds give you time to enter the premises and deactivate
the alarm before the siren sounds.
4. Delay Exit Mode - represented by the flashing of both the green and
red lights for 45 seconds
When both green and red lights are flashing, the control panel will
not recognize any remote sensors communicating to that zone.
These 45 seconds allow you time to exit the premises before that
zone is activated. When the lights stop flashing, both green and
red lights will remain on, which is now in DELAY ENTRY MODE.
(See above for information on DELAY ENTRY MODE).
5. Off - neither the green nor the red lights are on.
The Control Panel will not recognize any signals from a remote
sensor.
We have preprogrammed different combinations of the above modes to meet
different situations, (see STANDARD PROGRAMMING).
ADDITIONAL ARMING SEQUENCES
Below are three additional programming options you may want to use.
Option 1: Advanced Home 1 - use to secure the premises while staying
in the building. Delays the alarm to allow someone to enter the building and
deactivate the alarm.
SMARTHOME.COM™ 1-800-SMART-HOME 949-221-9200 http://www.smarthome.com Order #7307