Smarthome 7307 - Manual (Page 8)

– 14 –
STANDARD PROGRAMMING
Option 2: Home Sequence - To arm your system when someone
remains in the premises.
1. Press the current MPIN [ 0 0 0 ].
2. Press [ C ].
You hear a long beep. The arm light and the red lights in zones 3 and 4 go on. Both
the green and red lights flash in zone 1 for 45 seconds which gives you 45 seconds
to leave the premises before the system is activated. After 45 seconds, both the
green and red lights in zone 1 remain on. Upon re-entering the premises through
zone 1, you have 30 seconds till the alarm sounds. The system gives you 30
seconds from the time you activate the door/window sensor, for example opening
the front door, to get to the Control Panel to deactivate the system. Zone 2 remains
off which allows the person in the premises to move around without activating the
motion sensor. Zones 3 and 4 remain instant. If any sensor in zone 3 or 4 are
activated, the alarm sounds instantly.
Option 3: Night Sequence - To arm your system when there are people
in the premises and no one is expected to enter or exit. Example at
night when everyone is sleeping.
1. Press the current MPIN [ 0 0 0 ].
2. Press [ A ].
3. Press [ B ].
You hear a long beep. The arm light, the red light in zones 1, 3 & 4 go on. If any of
the sensors are activated in any of these 3 zones, the alarm is sounded instantly.
Zone 2, the motion sensor, remains off allowing movement throughout the premises.
TO DISARM THE SYSTEM USING THE KEYPAD ON THE CON-
TROL PANEL
1. Press the current MPIN [ 0 0 0 ].
2. Press [ # ].
All the lights but the AC PWR light go off. The system is now disarmed.
Note: If [MPIN,#] is entered when the system in not activated, the system
will default back to the last sequence before the unit was turned off.
Emergency Silent Alarm works in conjunction with the Emergency Dialer
(option), see Additional Accessories.
If under duress when disarming the system:
1. Enter the current MPIN [ 0 0 0 ].
2. Press [ B ] [ B ].
This will terminate the delay mode (stop the steady repeated beep) and return
to the previous arm mode. It will also send a signal to the Emergency Dialer
silently which will then automatically send a prerecorded message for help.
The Keychain Transmitter conveniently fits on any keychain. It allows you to
arm and disarm the system from a distance of approximately 100 feet from
the Control Panel. The distance will depend on what is between the key-
chain transmitter and the Control Panel. It also has a panic button that lets
you remotely activate the siren instantly.
Note: Make sure you press down on the transmitter for one full second or
the system may not respond.
– 15 –
TO ARM SYSTEM USING THE KEYCHAIN TRANSMITTER
There are 2 different arm options to choose from:
1. Press button #1, and the Control Panel will beep once.
The system will be armed in the Away Sequence. To be used to arm the
system when you are the last person leaving the premises. (see
page 13 for information on the Away Sequence).
Pressing button #1 will give you the same result as pressing:
MPIN, [ B ] , [ C ] on the keypad.
2. Press button #2, and the Control Panel will beep once.
The system will be armed in Home Sequence. To be used to arm the
system when someone remains in the premises. (see page 14 for
information on the Home Sequence).
Pressing button #2 will give you the same result as pressing: MPIN, [ C ]
on the keypad.
PANIC
2
1
3
KEYCHAIN TRANSMITTER (4B-434)
SMARTHOME.COM™ 1-800-SMART-HOME 949-221-9200 http://www.smarthome.com Order #7307