Setup menu, Advanced setup menu, Setting the projector using rs-232c or telnet – Sharp XG-P610X User Manual
Page 33
-33
Setting the Projector Using RS-232C or Telnet
SETUP MENU
(Main Menu)
[1]IP Address (Factory default setting : 192.168.150.2)
IP address settings. (Page
36
)
[2]Subnet Mask (Factory default setting :
255.255.255.0)
Subnet mask settings. (Page
36
)
[3]Default Gateway (Factory default setting : Not
Used)
Default gateway settings. (Page
36
)
[4]User Name (Factory default setting : Not Re-
quired)
Setting of user name for security protection. (Page
36
)
[5]Password (Factory default setting : Not Required)
Setting of password for security protection. (Page
37
)
[6]RS-232C Baud Rate (Factory default setting :
9600 bps)
Baud rate settings for the RS-232C terminals. (Page
37
)
[7]Projector Name
It is possible to assign a projector name. (Page
37
)
[8]DHCP Client
DHCP Client settings. (Page
37
)
[A]Advanced Setup
Enters ADVANCED SETUP MENU. (Page
38
)
[D]Disconnect All
Disconnect all connections. (Page
38
)
[V] View All Setting
Displays all setting values. (Page
34
)
Can also be used with ADVANCED SETUP MENU.
[S] Save & Quit
Save set values and quit menu. (Page
35
)
[Q]Quit Unchanged
Quit menu without saving setting values. (Page
35
)
Note
• The factory default settings for the projector are
as follows:
DHCP Client : OFF
IP address : 192.168.150.2
Subnet mask : 255.255.255.0
Default gateway : 0.0.0.0
ADVANCED SETUP MENU
[1]Auto Logout Time (Factory default setting : 5 min-
utes)
Setting of time until automatic disconnection of net-
work connection. (Page
38
)
[2]Data Port (Factory default setting : 10002)
Setting the TCP port number used when exchang-
ing data. (Page
38
)
[5]Network Ping Test
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally. (Page
39
)
[6]Accept IP Addr(1)
[7]Accept IP Addr(2)
[8]Accept IP Addr(3)
[9]Accept All IP Addr (Factory default setting : Ac-
cept All)
For improved security, it is possible to set up to three
IP addresses allowing connection to the projector.
Set IP addresses can be cancelled using [9] Accept
All IP Addr. (Page
39
)
[0] Search Port (Factory default setting : 5006)
Setting the port number used when searching for
the projector. (Page
40
)
[!] Restore Default Setting
Restores all setting values that can be set using the
menu to the default state. (Page
40
)
[Q]Return to Main Menu
Return to the main SETUP MENU. (Page
40
)
▼SETUP MENU
▼ADVANCED SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
setup>
******************** ADVANCED SETUP MENU ***********************
[1]Auto Logout Time
[2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1)
[7]Accept IP Addr(2)
[8]Accept IP Addr(3)
[9]Accept All IP Addr
[0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced>