Sanyo HEC-DR7700C - Manual (Page 12)

22 21
MASSAGING (MANUAL COURSES)
7
Adjust the height, width, speed, and strength of the massaging rollers.
There are some adjustments which are not possible, depending on the type of massage chosen.
(See page 23)
Adjusting the height of massaging rollers.
The approximate position of the massaging rollers
is indicated by the lamp on the remote control.
Refer to page 23 for details of the contents of massage.
For grasping shoulder massaging and spine stretching, shoulder
position is first measured. When the position of shoulder is not
correct, adjust the position of massaging rollers. (See page 18)
During massaging operation, the operation can be changed to
other manual massage, Whole Body Sensor Automatic Course or
Automatic Course.
It is possible to operate the upper body massage and lower body
massage simultaneously.
The massage will not start without pressing MANUAL button, even if
the MANUAL (UPPER BODY) MASSAGING buttons are pressed.
(In such a case, the MANUAL button flickers five times.)
Massaging of upper body
The massaging rollers are moved to the upper position and are stopped automatically approx. 15 minutes
after starting the operation. The buzzer sounds and the lamp on the remote control will turn off.
If a different course button (manual) is pressed during the course of operation, the massage will be
completed by operation of the timer approx. 30 minutes after starting the massage selected first.
Adjusting the width of the massaging rollers.
Press the button.
The width of the massaging rollers will
change each time the button is pressed
and is indicated by the lamp on the
remote control. (in five stages)
Press the button.
Adjusting the movement speed of massaging rollers.
Press the button.
The speed of the massaging rollers will change
each time the button is pressed, and is indicated
by the lamp on the remote
control. (in five stages)
Adjusting the strength of the massage.
Press the button.
The strength of the massage will change each
time the button is pressed, and is indicated by
the lamp on the remote
control. (in five stages)
The massaging rollers will move up if the UP( )
button is pressed continuously and move down
if the DOWN( ) button is pressed continuously.
6
Press the desired MANUAL (UPPER BODY)
MASSAGING button.
Finishes the massaging automatically by timer operation.
5
Press the MANUAL button.
MANUAL button
MANUAL (UPPER BODY)
MASSAGING buttons
4
Open the cover of the remote control.
Cover
Post
Hook
Post
Hook
When the button is pressed, the lamp of the remote control illuminates and the sole warmer
will turn on.
When the foot rest is fully lowered, the foot rest will rise a little.
When the massaging rollers are not located in the upper section, the massaging rollers will
move to the upper section and stop.
(During the movement, the characters of "ORIGIN" on the remote control flicker.)
1
Press the OPERATION ON/OFF button.
Sole warmer will be turned on or off each time the SOLE WARMER button is pressed.
(The button is illuminated while the sole warmer is on.)
If you feel that the sole warmer is too hot, turn it off by pressing the SOLE WARMER button.
3
Adjust the positions of the back rest and the foot rest.
(See page 13-15)
2
Turn the sole warmer on or off.
When the room temperature is low such as in winter, it takes some time to warm up or you
may barely feel warm.
If an excessive force is applied to the cover, it may be
detached. In such a case, re-attach the cover according
to the following procedure.
Place the hook on the underside of
cover around the post
on the underside
of the remote
control.
Slide the hook on the upper side of
cover around the post on the upper
side of the remote control until you
hear a clicking noise.
How to attach the cover
If you have felt abnormal physical sensation or want to stop the massager immediately To stop the massage during massaging operation.
Press the OPERATION ON/OFF button.
The massaging that corresponds to the pressed
button will stop.
(The Massaging rollers will stop at that point.)
All the massaging will stop and the chair will be
automatically brought to its home position.
(The massaging rollers are moved to the upper
position and remain in that position.)
Press the INSTANT STOP button.
All the massaging will stop and the lamp of the remote control
will turn off.
When you want to restart massaging, press the OPERATION
ON/OFF button. (The massaging rollers move to the upper
position and remain in that position.)
After the movement, repeat the operation from the beginning
of each massage.
Press the button for the current operation.