Samsung HLN617W1 - Manual (Page 9)

Installing Batteries in the Remote Control
With normal use, the batteries in the remote control should last about a year. If you notice a performance
degradation while using the remote, the batteries may need to be replaced. Make sure you replace both
batteries and do not mix old and new batteries in the remote control. If you won’t be using the remote
control for a long time, remove the batteries and store them in a cool dry place.
1 Slide the back cover all the way out
to open the battery compartment of
the remote control.
2 Install two AAA size batteries.
Make sure to match the “+” and
“–” ends of the batteries with the
diagram inside the compartment.
3 Slide the cover back into place.
17
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV. When using the remote,
always point it directly at the TV. The remote control can also operate your Set Top Box, VCR, cable box,
and DVD player.
Your New Wide TV
16
1. POWER
Turns the TV on and off.
2. S.MODE
Adjust the TV sound by selecting one of the
preset factory settings (or select your personal,
customized sound settings.)
3. P.MODE
Adjust the TV picture by selecting one of the
preset factory settings (or select your personal,
customized picture settings.)
4. +100
Press to select cable channels over 100 on TV.
5. VOL -, VOL +
Press to increase or decrease the volume.
6. MUTE
Press to mute the TV sound.
7. FAV.CH (Favorite Channel)
Press to switch between your favorite channels.
8. MENU
Displays the main on-screen menu.
9. STILL
Press to stop the action during a particular
scene. Press again to resume normal video.
10. P.SIZE
Press to change the screen size.
11. MODE
Selects a target device to be controlled by the
Samsung remote control (i.e., TV, VCR, Cable, or
DVD).
12. PRE-CH
Tunes to the previous channel.
13. TV/VIDEO
Press to display all of the available video
sources (i.e., TV, STB, VCR, DVD, DTV, PC).
14. CH and CH
(Channel Up/Down)
Press CH or CH to change channels.
15. INFO
Press to display information on the TV screen.
16. EXIT
Press to exit the menu.
17. UP, Down, Left, Right
( ▲, ▼, œ, √)/ENTER
Press to select highlight up, down, left, or right.
While using the on-screen menus, press ENTER
to activate (or change) a particular item.
18. MTS(Multichannel
Television Stereo)
Press to choose stereo, mono or Separate Audio
Program (SAP broadcast).
19. SURROUND
Press to hear the Dolby surround effect.
20. ADD/DEL
Press to add or erase channels in the TV’s
memory.
Use the ADD/DEL button to memorize/erase
the fine tuning after fine tuning channels.
21. SLEEP
Press to select a preset time interval for
automatic shutoff.
22. PIP
Activates picture in picture.
23. SET
Used during set up of this remote control, so
that it will work compatibly with other devices
(VCR, STB, cable box, DVD, etc.)
24. DNIe
Activates DNIe (Digital Natural Image engine).
25. PIP controls
SWAP; Exchanges the video signal that is
currently displayed on the main screen with the
signal in the PIP window.
SIZE; Press to make the PIP window larger or
smaller.
CH(PIP); Displays the available channels in
sequence. (These buttons change channels in
the PIP window only.)
26. VCR controls
Controls VCR tape functions: Rewind, Play, Fast
Forward, Stop, Pause.
27. RESET
If your remote control is not functioning
properly, take out the batteries and press the
reset button for about 2~3 seconds. Re-insert
the batteries and try using the remote control
again.