Spalding 214973A - Manual (Page 5)

04/03 P/N 214973A 5
INSTRUCTIONS
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS
OWNERS MANUAL
1. Mark pole sections with tape as shown.
2. IMPORTANT! Bounce pole top (1) and middle section (2) together as shown
until they no longer move toward taped reference mark. Upright assembly.
NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap.
3. IMPORTANT! Holes in top (1) and bottom pole (3) sections MUST align to
correctly position elevator system toward playing surface. Add bottom pole
section (3) to assembly as shown and bounce until completely tight. NOTE: Pole
sections should have a 3-1/2" (9 cm) minimum overlap.
4. Install wheels (17) onto axle (28) and wheel bracket (25) with push caps (29) as
shown.
5. Position base as shown. Secure wheel bracket assembly with bolt (16) and nut (15)
as shown.
6. Install rod (4) through holes in bottom pole section (3) and eyebolt (5).
Insert pole assembly into tank (6) and through center hole on wheel assembly as
shown. Secure pole assembly with strap (74), washer (11) and lock nut (8). NOTE:
Two people recommended for this step.
7. Secure base struts (9) to pole using bolt (10) washers (11) and nut (12) as shown.
Rotate the non-secured ends of base struts (9) as shown.
8. Secure base struts (9) to base using bolt (14) washers (11) and nut (15).
9. Install upper pivot bracket (18) to front of base using bolt (19), washer (20) and nut
(8) as shown.
10. Insert bolt (21) through lower pivot bracket (22) as shown, bolt (21) will be secured
during step 12. Carefully place base assembly on its side. Install lower pivot
bracket (22) with bolt (23), washers (20) and lock nut (8) as shown.
11. Secure both hinge tubes (24) to second wheel bracket (25) with carriage bolts (26)
and flange nuts (15).
12. Install wheels (27) onto axle (28) and wheel bracket (25) with push caps (29) as
shown.
13. Position base as shown. Secure wheel bracket assembly with disc (30), washer
(20) and nut (8) as shown. NOTE: Two people recommended for this step.
14. Carefully reposition entire assembly as shown. IMPORTANT! Two people
recommended for this step.
15. Snap tinnerman nut (31) onto inner channel (32). Place inner channel into outer
channel (33) as shown.
16. Slide handle (34) into position as shown and secure with bolts (35), washers (11),
and nuts (15). Tighten completely.
17. Install bolt (36), washers (11), and nut (37) as shown. Tighten until washers (11)
are no longer loose. NOTE: Do not over tighten. Assemble trigger (38) to handle
assembly (34, 32, 31) as shown and secure with bolt (39) and washer (11). Tighten
completely.
18. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
Install trigger return spring (40) to handle assembly (32, 33) as shown.
19. Attach Accuheight label (41) to inner channel (32).
20. Attach spring (44) to pins (43) and install pins (43) onto pole mount bracket (45).
Attach other spring (44) to opposite side. NOTE: Gently enlarge eyelets of spring
with pliers if springs do not fit over pins.
WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
21. Install pole mount assembly and reinforcement bracket (47) with carriage bolts (46)
to pole as shown. Tighten flange nuts (15) completely.
22. Push back sliding pin (43) as shown in Figure A to fit adjustable system assembly
through pole mount assembly. Then attach spring covers (48 & 49) onto pole
mount bracket (45) with bolt (50), and nut (15) as shown in Figure B.
23. Install spacers (51) onto backboard brackets (52) with bolts (53, 54) and lock nuts
(55, 37) as shown.
24. Assemble lower elevator tubes (56) as shown. NOTE: Tighten bolt (57) in lock nut
(58) until flush (even) with lock nut’s outer edge.
IMPORTANT! It is necessary for all parts to be installed for this mechanism
to work safely and properly. NOTE: Test fit bolts into holes of brackets (52) and
carefully rock them in a circular motion to ream out paint from holes if necessary
25. Place board spacers (75) into board as shown. Bend brackets (52) to line up with
holes in board. Insert bolts (62) into holes as shown. Tighten completely.
NOTE: Rim mounting nuts (15) and bolts (60) supplied with rim hardware.
26. Assemble upper elevator tubes (63) to backboard brackets (52) as shown.
NOTE: Tighten bolt (57) in lock nut (58) until flush (even) with lock nut’s outer
edge.
27. Support pole on sawhorse. Attach backboard assembly to top pole section (1) as
shown. Then install pole cap (64). NOTE: Two people are recommended for this
step. Use caution; elevator assembly is heavy.
28. Install upper elevator tubes (63) to triangle plates (66) as shown.
Next, Install handle assembly (32, 33) to lower elevator tubes (56) using bolt (57),
spacers (67), and nut (58) as shown. NOTE: Tighten bolt (57) in lock nut (58) until
flush (even) with lock nut’s outer edge. NOTE: Before going on to next step, set
adjustable system assembly to the 10’ (3.05 m) setting.
29. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
Insert bolt (57) through left side upper elevator tube (63), then stretch spring (68)
onto bolt (57). Insert bolt (57) through right side upper elevator tube (63) and
secure with nut (58).
30. Attach front cover (72) to hinge tubes (24) using carriage bolt (61) and flange nuts
(15) as shown.
WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY,
MAY TIP OVER.
31. Apply height and moving label (73) to front of pole as shown.
32. Roll completed assembly to desired playing area. Secure assembly to ground using
strap (74) and tie down stake (7). Fill tank with 34 gallons of water. IMPORTANT!
Add two gallons (7.6 Liters) of non-toxic antifreeze in sub-freezing climates.
Add two gallons (7.6 liters) to tank to prevent freezing in sub-freezing climates.
Snap cap (42) into place.
33. WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.
Grasp handle and depress lever.
34. Push toward pole while holding lever. Raise or lower lever to desired height while
pushing forward on handle.
35. Release handle making sure that horizontal pin (43) is locked into slot.
WARNING: USE OF THIS PRODUCT WITHOUT PROPER
INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS
ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE
TO FOLLOW DIRECTIONS CAREFULLY.
36. Install net clips as shown. (See illustration)
37. Install net as shown. (See illustration)
BEFORE YOU START!
To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is
required. Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates. Carefully rock them in a
circular motion to ream out any excess paint from holes if necessary.