Woodstock SHOP FOX W1706 - Manual (Page 54)

-52-
Model W1706 (Mfg. Since 3/13)
SE
RV
IC
E
Troubleshooting
This section covers the most common problems and corrections with this type of
machine. WARNING!.DO.NOT.make.any.adjustments.until.power.is.disconnected.and.
moving.parts.have.come.to.a.complete.stop!
PROBLEM POSSIBLE.CAUSE CORRECTIVE.ACTION
Motor will not start. 1. Low voltage.
2. Open circuit in motor or loose
connections.
3. Faulty start capacitor.
1. Check power supply for proper voltage.
2. Inspect all lead connections on motor and magnetic
switch for loose or open connections.
3. Replace start capacitor.
Fuses or circuit breakers
trip open. 1. Short circuit in line cord or plug.
2. Short circuit in motor or loose
connections.
3. Incorrect fuses or circuit breakers
in power supply.
1. Inspect cord or plug for damaged insulation and
shorted wires and replace extension cord.
2. Inspect all connections on motor for loose or
shorted terminals or worn insulation.
3. Install correct fuses or circuit breakers.
Motor overheats. 1. Motor overloaded.
2. Air circulation through the motor
restricted.
1. Reduce load on motor.
2. Clean motor to provide normal air circulation.
Motor fails to develop full
power. 1. Power line overloaded with other
electrical devices.
2. Low power from the power source.
1. Reduce load on power line.
2. Request a power check from the power company.
Motor stalls (resulting in
blown fuses or tripped
circuit). 1. Short circuit in motor of loose
connections.
2. Low voltage.
3. Incorrect fuses or circuit breakers
in power line.
4. Motor overloaded.
1. Inspect connections on motor for loose or shorted
terminals or worn insulation.
2. Correct the low voltage conditions.
3. Install correct fuses or circuit breaker.
4. Reduce load on motor.
Machine slows when
operating. 1. Excessive feed rate.
2. Dull blade.
3. Incorrect blade for operation.
4. Binding the blade when cutting
curves.
5. Workpiece wet.
1. Reduce feed rate.
2. Sharpen/replace blade.
3. Use correct blade for workpiece.
4. Make more relief cuts; use correct blade width for
operation.
5. If moisture content is higher than 20%, sticker and
allow to dry.
Blade does not run evenly
on wheels or runs off. 1. Tracking is not properly adjusted.
2. Wheels are not coplanar. 1. Properly adjust blade tracking (see Page.14).
2. Adjust wheel alignment (see Page.47).
Blade slows when cutting;
machine makes a squealing
noise upon startup. 1. Belt loose.
2. Belt excessively worn. 1. Adjust belt tension (see Page.43).
2. Replace belt (see Page.44).
Ticking sound when
bandsaw is running. 1. Blade weld contacting guide bear-
ings.
2. Motor fan or cover damaged.
3. Damaged blade; bent teeth.
1. Use a stone to smooth blade weld.
2. Replace.
3. Replace blade.
Blade contacting table
insert. 1. Excessive side pressure on blade
when cutting.
2. Table not properly adjusted.
1. Reduce side pressure on blade.
2. Properly align the table with the blade (see
Page.19).
Excessive vibration when
bandsaw is running. 1. Machine sits on floor unevenly.
2. Wheels not coplanar.
3. Tires incorrectly installed.
4. Belt worn out.
5. Bent or damaged blade.
6. Wheel(s) out of balance. 1. Adjust rubber feet; shim if necessary.
2. Adjust wheel alignment (see
Page.47).
3. Check/re-install/replace.
4. Replace belt (see
Page.44).
5. Replace blade (see Page.39).
6 Replace wheel(s).