Sharp MD-X60H - Manual (Page 44)

<P=005>
(Continued)
ENTER
TIMER/
DELETE
To check the timer setting:
①
Whilst in the timer stand-by mode, press the TIMER/DELETE button.
②
Within 10 seconds, turn the jog dial so that the "TIMER CALL"
display appears.
③
Within 10 seconds, press the ENTER button.
● The timer settings will appear in order, and then the original display
will reappear.
To cancel the timer operation:
If the power is turned on, the timer will be cancelled.
The timer operation can also be cancelled as follows.
①
Whilst in the timer stand-by mode, press the TIMER/DELETE button.
②
Turn the jog dial so that the "TIMER CANCEL" display appears.
③
Within 10 seconds, press the ENTER button.
● The timer operation will be cancelled ("TIMER" or "TIMER REC" will
go off.) The start and stop times will be stored.
Jog dial
■ Sleep operation
The radio, compact disc and MiniDisc can all be turned off automat-
ically.
1
Play the desired sound source.
2
Press the TIMER/DELETE button.
3
Within 10 seconds, turn the jog dial so that the "SLEEP" display
appears.
4
Within 10 seconds, press the ENTER button.
● If you do not need to change the time, go to step 5.
To change the sleep time:
Whilst the sleep time is displayed, turn the jog dial to adjust the time.
(Maximum: 2 hours - Minimum: 1 minute)
The amount of sleep time can also be changed during the sleep oper-
ation.
● 2 hours - 5 minutes → 5-minute intervals
● 5 minutes - 1 minute → 1-minute intervals
5
Press the ENTER button.
6
The unit will enter the stand-by mode automatically after the preset
sleep time has elapsed.
● The volume will decrease gradually 1 minute before the preset sleep
time has elapsed. At this time, you cannot change the volume.
To confirm the sleep timer setting:
①
Press the TIMER/DELETE button.
②
Turn the jog dial so that the "SLEEP" display appears.
To cancel the sleep operation:
If the unit enters the stand-by mode, the sleep operation will be can-
celled. The sleep operation can also be cancelled as follows if you
cannot set the unit to the stand-by mode during recording.
①
Press the TIMER/DELETE button.
②
Turn the jog dial so that the "SLEEP OFF" display appears.
③
Within 10 seconds, press the ENTER button.
● The sleep operation will be cancelled. ("SLEEP" will go off.)
Notes:
● Once the sleep time is set, it will remain the same duration until the
setting is changed.
● The sleep functions of this unit cannot be used to control equipment
connected to this unit. You must use the sleep functions of the other
equipment, if it has them.
■ Simultaneous sleep and timer operation
To use sleep and timer playback in combination:
①
Perform steps 1 - 13 on page 41 "To select the timer playback
mode".
②
Perform steps 1 - 5 on page 43 "Sleep operation".
③
Perform steps 1 - 2 on page 41 "Setting timer playback".
To use sleep and timer recording in combination:
①
Perform steps 1 - 12 on page 42 "To select the timer recording
mode".
②
Perform steps 1 - 5 on page 43 "Sleep operation".
③
Perform steps 1 - 2 on page 42 "Setting timer recording".
Sleep timer setting
Timer playback
(record) setting Timer playback
(record) start
1 minute - 2 hours Desired time
Sleep operation will
automatically stop. End time
Notes:
● When the CD or MD is played to the end, playback will stop before
the stop time.
If you wish to play to the stop time, set repeat play for the CD or
MD.
● Timer recording starts about 15 seconds before the start time.
3
4
5
MD-X60H(SUK) TINSE0227AWZZ
43