Samsung SID-500 - Manual (Page 22)

Troubleshooting
Input Voltage
Input Current
Power Consumption
Size
Total Pixels
Effective Pixels
Optics
Min. Focus Distance
D. ZOOM
Angle Field of view
Scanning System
Synchronization
Frequency
Resolution
Video Output
S/N (Y signal)
Min. Illumination
Backlight Compensation
Day & Night
Gain Control
White Balance
Electronic shutter
speed
O.S.D
Motion Detection
SSNR
Focus
Zoom Movement Speed
IRIS Control
Lens Initialize
Camera Title
AC 24V(±10%), DC 12V(±10%)
290mA(Steady-state)
460mA(Zoom, Focus, Day&night motor operating)
DC12V/ AC24V - 3.5W Normal
- 5.5W Max (Zoom, Focus, Day&Night motor operating)
1/4 inch, Interline Transfer CCD
811(H) x 508(V) 795(H) x 596(V)
768(H) x 494(V) 752(H) x 582(V)
10X, f=3.8 to 38.0mm(F1.8)
1,500mm
OFF/ON (X2 ~ X10)
H : Appr. 51.2˚(Wide) to 5.58˚(Tele)/V : Appr. 39.3˚(Wide) to 4.27˚(Tele)
2:1 Interlace
Internal / Line-Lock
H: 15.734KHz / V: 59.94Hz H: 15.625KHz / V : 50.00Hz
500 TV Lines(Min.) : Color (WIDE) / 570 TV Lines(Min.) : B/W (WIDE)
CVBS : 1.0Vp-p/75Ω(VBS EXT)
50 dB (AGC Off, Weight ON)
[email protected], [email protected](Sens-up), Color/[email protected](B/W)
LOW/MIDDLE/HIGH/OFF Selectable
Auto1, Auto2, COLOR, B/W(ICR)
Normal, High, OFF Selectable
ATW(INDOOR(3,000K~10,500K), OUTDOOR(1,800K~10,500K))/AWC/MANUAL
Built-In
ON/OFF(4 Programmable Zone per Screen)
Low, Middle, High, Off
Auto / Manual / One push
1.67sec : Wide to Tele 1.75sec : Wide to Tele
Auto, Manual
Built-In
OFF/ON (Displayed 15 characters)
SID-500N SID-500P
C
C
D
P
O
W
E
R
S
y
n
c.
O
P
T
I
C
S
E
L
E
C.
COLOR CCD CAMERA User’s Manual 43 COLOR CCD CAMERA User’s Manual 42
AUTO (X128~1/60sec~1/120,000sec)
Sens-up and Sens-up Limit is
selectable, Flickerless
AUTO (X128~1/50sec~ 1/120,000sec )
Sens-up and Sens-up Limit is
selectable, Flickerless
Refer to the following table if you are experiencing trouble with your camera.
Contact an authorized technician if the table does not provide you with a
solution to the trouble.
Problem Solution
• Check the power cable and the wiring between the
camera and the monitor.
• Ensure proper video cable connection (Video Out Jack).
• The lens could be dirty. Clean with a soft, clean
piece of cloth.
• Adjust monitor settings.
• Adjust camera position if exposed to a strong light
source.
• Adjust the monitor's contrast level.
• Set the intermediate device, if in use, to 75Ω/ Hi-z
(refer to p.16).
• Check the power source for compliance with
specifications.
• Ensure that the feature is set to ON.
• Adjust and configure WHITE BAL.
• The camera may be facing the sun or a fluorescent
light. Adjust the position of the camera.
• The camera may be connected to a DC power
source. Connect to an AC power source.
• Check external SYNC signal frequency (should be
60Hz for NTSC, 50Hz for PAL).
No display
Dim display
Dark display
Uneven colors
Flickering
Can't select LL mode
LL is not function
properly.
The camera is not
functioning properly and
its surface is hot
Motion Detection
feature is not active.
Specifications