Sony UP-970AD - Manual (Page 16)

A
n
al
o
g
M
o
de
Adjustments and Settings Using the Menu
16
Menu List
This section describes the menus displayed as you turn
the jog dial. The setting surrounded by
indicates the factory setting.
Item Function Settings
AGC To adjust the
input signal to the
optimum printing
level AG:ON: Adjusts the input
signal to the optimum level,
when the printout image
appears too dark or too
light.
[AG:OFF]: Normally select
this setting.
BACK: Cancels the setting
change and returns to the
item selection column.
ASPCT a) To select the
aspect ratio AS:1:1: Prints a video
signal with an aspect ratio
of 1:1.
[AS: 4:3]: Normally select
this setting.
BACK: Cancels the setting
change and returns to the
item selection column
BEEP To turn operation
tones ON and
OFF. Error tones
sound regardless
of setting. BE: OFF: The operation
tone does not sound.
[BE: ON]: The operation
sounds.
BACK: Cancels the setting
change and returns to the
item selection column.
CLEAN To start head
cleaning [CLN: OK]: Starts the head
cleaning. Be sure to use the
supplied cleaning sheet.
BACK: Cancels the head
cleaning and returns to the
item selection column.
CLEAR To delete images
stored in memory. [CLR: OK]: Deletes all
images stored in memory.
BACK: Cancels CLEAR
and returns to the item
selection column.
AT . CUT
(UP-990AD
only function)
To turn on and off
automatic cutting
of completed
prints. CT:OFF: Cuts the paper
when the CUT button is
pressed.
[CT:ON]: Cuts the paper
automatically.
BACK: Cancels the setting
change and returns to the
item selection column.
DIR
b)
To select whether
the top or bottom
of the screen is to
be printed first DI: REV: Starts to print in
the reverse direction (from
the top of the screen).
[DI: NOR]: Starts to print in
the normal direction (from
the bottom of the screen).
BACK: Cancels the setting
change and returns to the
item selection column.
FEED
(UP-990AD) To set the top and
bottom margin of
a print. [FE: 0]to FE:15: Sets the
margin to one of 16 steps
from 0 to 15. An increase of
one step increases the top
and bottom margin by 5
mm. The top and bottom
margin can be increased to
75 mm. The “0” setting is
the default value, which
still provides a narrow
margin between two
images.
BACK: Cancels the setting
change and returns to the
item selection column.
FEED
(UP-970AD) To select the
paper feed
method used after
printing. [FE: ON]: Increases the
margin between prints.
FE:OFF: Sets when
reducing the margin or
when printing multiple
images on the same sheet.
This reduces the margin
between images allowing
you to print more images
per roll. However, with this
setting, the FEED button
must be pressed before
cutting the paper.
BACK: Cancels the setting
change and returns to the
item selection column.
FRAME To select the
color of the frame
between images
in multi-picture
mode. FR:BLK: Sets the frame
color to black.
[FR:WHT]: Sets the frame
color to white.
BACK: Cancels the setting
change and returns to the
item selection column.
GAMMA To select the tone
of the printouts
(density
gradation) GA:3: TONE 3 Hard
gradation
GA:2: TONE 2 Soft
[GA:1]: TONE 1 Standard
gradation
BACK: Cancels the setting
change and returns to the
item selection column.
IMAGE To set the printout
to either positive
printout or
negative printout IM:NEG: Makes negative
printouts.
[IM:POS]: Makes normal
printouts.
BACK: Cancels the setting
change and returns to the
item selection column.
INFO To select whether
or not the print
conditions (such
as contrast,
bright, gammas
and sharpness
information) are
printed under the
image IF:ON: Prints the
information.
[IF:OFF]: Does not print the
information.
BACK: Cancels the setting
change and returns to the
item selection column.
Item Function Settings