KORG D3200 - Manual (Page 163)

153
Effect
Algorithm list
Program list
Stereo type
Algorithm
Monaural type
Algorithm
: ER Level, : Reverb Level
These parameters set the early reflection level and reverb level.
Changing these parameter values allows you to simulate the
type of walls in the room. That is, a larger “ER Level” simulates
a hard wall, and a larger “Reverb Level” simulates a soft wall.
This effect is only the early reflection part of a reverberation
sound, and adds presence to the sound. You can select one of
the four decay curves.
: Type
This parameter selects the decay curve for the early reflection.
This multitap delay outputs three Tap signals to the left,
right, and center respectively. You can also adjust the left and
right spread of the delay sound.
: High Damp, : Low Damp
These parameters set the damping amount of high range and
low range. The tone of the delayed sound becomes darker and
lighter as it feeds back.
: Spread
This parameter sets the pan width of the effect sound. The
stereo image is widest with a value of “50,” and the effect
sound of both channels is output from the center with a value
of “0.”
This is a stereo delay, and can by used as a cross-feedback de-
lay effect in which the delay sounds cross over between the
left and right by changing the feedback routing.
The left and right Multitap Delays have two taps respective-
ly. Changing the routing of feedback and tap output allows
you to create various patterns of complex effect sounds.
EQ Trim –15...+15dB
Sets the equalizer trim level
LEQ Gain (Pre LEQ Gain) –15...+15dB
Sets the gain of Low EQ
HEQ Gain (Pre HEQ Gain) –15...+15dB
Sets the gain of High EQ
P.DlyThru (Pre Delay Thru) 0...100%
Sets the mix ratio of non-delay sound
Rev Level (Reverb Level) 0...100%
Sets the reverberation level
ER Level 0...100%
Sets the level of early reflections
7: Early Reflection
Type Sharp, Loose, Modulated, Reverse
Selects the decay curve for the early reflection
ER Time 10...800msec
Sets the time length of early reflection
Predly (Pre Delay) 0...200msec
Sets the time taken from the original sound to the first early
reflection
EQ Trim –15...+15dB
Sets the equalizer trim level
LEQ Gain (Pre LEQ Gain) –15...+15dB
Sets the gain of Low EQ
HEQ Gain (Pre HEQ Gain) –15...+15dB
Sets the gain of High EQ
Dry:Wet Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
8: L/C/R Delay
L Time (L Delay Time) 0...2.730sec
Sets the delay time of TapL
C Time (C Delay Time) 0...2.730sec
Sets the delay time of TapC
R Time (R Delay Time) 0...2.730sec
Sets the delay time of TapR
Dry:Wet Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
L LevelL (Delay Level) 0...100%
Sets the output level of TapL
C LevelC (Delay Level) 0...100%
Sets the output level of TapC
R LevelR (Delay Level) 0...100%
Sets the output level of TapR
Spread 0...100%
Sets the width of the stereo image of the effect sound
Fdback (C) (Feedback (C Delay)) –100...+100%
Sets the feedback amount of TapC
Fb.LoDamp (Feedback Low Damp) THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
Fb.HiDamp (Feedback High Damp) 53Hz...20.0kHz, THRU
Sets the damping amount in the high range
In Level (Input Level) 0...100%
Sets the input level to the effect
9: Stereo/Cross Delay
L Time (L Delay Time) 0...2.730sec
Sets the left delay time
R Time (R Delay Time) 0...2.730sec
Sets the right delay time
Type (Stereo/Cross) Stereo, Cross
Switches between stereo delay and cross-feedback delay
Dry:Wet Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
L Fdback (L Feedback) –100...+100%
Sets the feedback amount for the left channel
R Fdback (R Feedback) –100...+100%
Sets the feedback amount for the right channel
LoDamp (Low Damp) THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
HiDamp (High Damp) 53Hz...20.0kHz, THRU
Sets the damping amount in the high range
Spread 0...100%
Sets the width of the stereo image of the effect sound
In Level (Input Level) 0...100%
Sets the input level to the effect
10: St. Multitap Delay
(Stereo Multitap Delay)
Tap1Time 0...2.730sec
Sets the delay time of Tap1
Tap2Time 0...2.730sec
Sets the delay time of Tap2
Type Normal, CrossFdback, CrossPan1, CrossPan2
Switches the left and right delay routing
Dry:Wet Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Tap1Level 0...100%
Sets the output level of Tap1
Tap2Level 0...100%
Sets the output level of Tap2
T1.Fdback (Tap1 Feedback) –100...+100%
Sets the Tap1 feedback amount
Spread 0...100%
Sets the width of the stereo image of the effect sound
Stereo type
Algorithm