Kenwood DT-7000S - Manual (Page 12)

Lock Code Setup
If you have locked any streams in the Channel Lock mode, you will need to enter a 4-
digit lock code to unlock them. The factory default lock code is “1 1 1 1”.
You can change the Lock Code to your own preference:
1. While in the Setup Mode, turn the
CATEGORY jog dial (unit) or press
the CAT buttons (remote) until the
Lock Code Setup screen appears
(top, right):
2. Turn the CH/PRESET jog dial (unit)
or press the CH buttons (remote).
The Lock Code screen appears
(second, right):
3. Using the number buttons, enter
the factory default code “1 1 1 1”.
The screen’s second line will
change from “_ _ _ _” to “* * * *”.
• If you enter an incorrect number,
use the left CAT button or jog dial
to delete the incorrect number;
then re-enter the correct one.
4. Press the MEMO button. The Enter
New Lock Code screen appears
(right).
• If you entered the code incorrect-
ly, “Code Error” will be displayed,
and the Enter New Lock Code
screen reappears. Repeat Steps
3 – 4.
5. Using the number buttons, enter your new 4-digit code. The screen’s second line will
change from “_ _ _ _” to “* * * *”.
6. Press the MEMO button. The Confirm Number screen appears (below).
7. Re-enter your new 4-digit code. The
screen’s second line will change
from “_ _ _ _” to “* * * *”.
8. Press the MEMO button. The display
will change to “New Code
Confirmed”
• If you entered the code incorrect-
ly, “Code Error” will be displayed, and the Enter New Lock Code screen reappears.
Repeat Steps 5 – 8.
Startup Mode
You can select which screen is displayed when you turn the DT-7000S’s power on.
1. While in the Setup Mode, turn the
CATEGORY jog dial (unit) or press the
CAT buttons (remote) until the
Startup Mode screen appears (right):
2. Use the CH/PRESET jog dial (unit) or
the CH buttons (remote) to highlight
the screen you want for Startup:
Normal Operation, Channel List (Stream List) or Category List (see pages 7 – 8).
Push the SETUP button to exit.
Output Level
You can adjust the DT-7000S’s output
level so it matches other sources in your
audio system.
1. While in the Setup Mode, turn the
CATEGORY jog dial (unit) or press the
CAT buttons (remote) until the Output
Level screen appears (right):
2. Use the CH/PRESET jog dial (unit) or the CH buttons (remote) to select the desired
output level.
• “High” is 0dB, “Medium” is –3dB and “Low” is –6dB.
Push the SETUP button to exit.
Antenna Signal
This screen shows the quality of the SIRIUS satellite signal that’s being received, to help
you find the best location for the antenna.
1. While in the Setup Mode, turn the
CATEGORY jog dial (unit) or press the
CAT buttons (remote) until the Antenna
Signal screen appears (right):
• After a few seconds the signal
quality bars will indicate how well
the antenna is receiving the
SIRIUS satellite signal.
2. Find a location for the antenna that illuminates the maximum number of bars.
• After moving the antenna, wait at least 2 seconds before moving it again, to enable
the unit to process the signal.
3. Due to the moving paths of the SIRIUS satellites, it is possible for the signal to change
over time. In most cases, signal should be available continuously, however, it
may be temporarily blocked in some antenna locations in home installations. Be sure
to check the Antenna Signal screen if there is a loss of signal or audio.
Experimentation with antenna placement in the home or outside may be necessary to
ensure continuous reception.
• See page 5 for information about properly locating the SIRIUS antenna.
DT-7000S Instruction Manual 12
Lock Code Screen
Enter New Lock Code Screen
Confirm Number Screen
Startup Mode Screen
Antenna Signal Screen
Output Level Screen
Lock Code Setup Screen