Lennox Hearth EBVI30 - Manual (Page 11)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 11
To light the burner, rotate the gas valve control
knob counterclockwise to the “ON” position
then turn “ON” the off/on switch mounted
on the surround assembly (see Figures 1 &
2 on Page 3) or operate the burner with the
optional remote control, wall thermostat or
control switch.
With proper care and maintenance, your appli-
ance will provide many years of enjoyment. If
you should experience any problem, fi rst refer
to the troubleshooting guide in this manual. If
problem persists, contact your Lennox Hearth
Products Dealer.
BLOWER OPERATION
When the insert heats up, the blower will auto-
matically be turned on by the fan disc located
under the fi rebox bottom on the front left side.
It will come on at the speed determined by the
rheostat located on the side surround panel (see
Figure 4 on Page 4). To adjust the blower speed,
dial the rheostat to the desired speed setting.
Rotate the dial down (clockwise), just past the
click (the fi rst ON position) for the highest speed
setting. Turning the knob further clockwise will
provide slower blower speeds.
Note: If the rheostat is not turned “on,” the
blower will not operate.
Proper Pilot Flame Appearance
MILLIVOLT APPLIANCE CHECKOUT
Light the pilot by following the instructions on
Page 15 or 16 of this manual.
The pilot fl ame should be steady, not lifting
or fl oating. Flame should be blue in color with
traces of orange at the outer edge. The top 3/8"
(10 mm) at the pilot generator (thermopile)
and the top 1/8" minimum (tip) of the quick
drop out thermocouple should be engulfed
in the pilot fl ame. The fl ame should project 1"
(25 mm) beyond the hood at all three ports
(Figure 25).
Replace logs if removed for pilot inspec-
tion.
Figure 25
Fireplace Warning Label
(Provided in Accessory Package)
FIREPLACE REQUIREMENTS
IMPORTANT: When installing this appliance
into a factory built fi replace or heatform, the air
fl ow within and around the fi replace shall not
be altered by the installation of the insert (i.e.
DO NOT BLOCK louvers or cooling air inlet or
outlet ports, circulating air chambers in a steel
fi replace liner or metal heat circulator).
CAUTION: The factory built fi rebox must
accept the insert without modifi cation other
than removing bolted or screwed together
pieces such as smoke shelf/defl ectors, ash lips,
screen or door tracks, log grates, refractory and
damper assemblies. Any fi replace component,
which is removed, must be retained so they
can be reinstalled to restore the fi replace to
its original operating condition. The removal
of any part must not alter the integrity of the
outer shell of the pre-engineered fi replace
cabinet in any way.
If any components are removed from (or altered)
from the existing fi replace, a Warning Label
(see below) must be affi xed inside the fi replace
fi rebox, so that it shall be visible upon removal of
the fi replace insert. Note: RTV high temperature
silicone is an approved adhesive.
WARNING
THIS FIREPLACE HAS BEEN ALTERED TO
ACCOMMODATE A FIREPLACE INSERT
AND SHOULD BE INSPECTED BY A QUALI-
FIED PERSON PRIOR TO RE-USE AS A
CONVENTIONAL FIREPLACE.
Figure 26
1/8" Min.
(3 mm)
Thermocouple
Igniter Rod
Hood
3/8" Min.
(9 mm)
Thermopile
Pilot
Nozzels
WIRING DIAGRAMS
Wiring diagrams are provided here for refer-
ence purposes only. This information is also
provided on schematics attached directly to the
appliance on a pullout panel located within the
control compartment.
WARNING: THE POWER CORD MUST BE
PLUGGED DIRECTLY INTO A PROPERLY
GROUNDED THREE-PRONG 120 VOLT,
60 HZ WALL RECEPTACLE. DO NOT CUT
OR REMOVE THE GROUNDING PRONG
FROM THIS PLUG. DO NOT ROUTE
POWER CORD UNDER OR IN FRONT
OF APPLIANCE.
Room Air Circulation Blower
Figure 27
Fan Disc
Rheostat
Blower
Assembly
Power Cord
Black
Hot (Live)
Red
Black
Black
Black
120 V AC
Blower Wiring Diagram
IMPORTANT: BLOWER GROUND WIRE
WITH POWER CORD GREEN WIRE
SHOULD BE ATTACHED TO THE GROUND
SCREW. FAILURE TO DO SO WILL
RESULT IN A POTENTIAL SAFETY
HAZARD. THE APPLIANCE MUST BE
ELECTRICALLY GROUNDED IN ACCOR-
DANCE WITH LOCAL CODES OR, IN
THE ABSENCE OF LOCAL CODES, THE
NATIONAL ELECTRICAL CODE, ANSI/
NFPA 70 - LATEST EDITION. (IN CANADA,
THE CURRENT CSA C22-1 CANADIAN
ELECTRICAL CODE - LATEST EDITION.
White
(Neutral)
Green
(Ground)
CAUTION
Label all wires prior to discon-
nection when servicing con-
trols. Wiring errors can cause
improper and dangerous appli-
ance operation.